datasheetbank_Logo
Integrated circuits, Transistor, Semiconductors Search and Datasheet PDF Download Site

CMX882 View Datasheet(PDF) - CML Microcircuits

Part Name
Description
View to exact match
CMX882
CMLMICRO
CML Microcircuits CMLMICRO
CMX882 Datasheet PDF : 70 Pages
First Prev 11 12 13 14 15 16 17 18 19 20 Next Last
FRS Signalling Processor
CMX882
1.5.3 Receive Mode
The CMX882 can receive voice and various signal formats: CTCSS tone, DCS code, XTCSS / In-band
tones and FFSK/MSK data at 1200 and 2400bps. Reception of each of these signal types can be
independently enabled/disabled by C-BUS command. If enabled, an interrupt will be issued to notify the
host µC of the presence and type of the incoming signal.
In receive mode the CMX882 performs signal type identification in 2 frequency bands, sub-audio (60 -
260Hz) and voice band (300 - 3kHz), to determine what type of signal is being received. When an
enabled signal is detected this will be indicated to the host over the C-BUS and the CMX882 will continue
to process the received signal in its band. Identification / process mode will continue in the other band.
The CMX882 can process voice and simultaneously identify and process at least 2 other signal types
(one in the sub-audio in parallel with one in the voice band). See Table 2 for valid combinations. These
combinations can be used with Voice Processing, if desired.
The receive gain and audio output amplifier gain can be adjusted by the host µC, via C-BUS command,
to provide receive signal level adjustment and output volume control or muting.
Table 2 Concurrent Rx Signalling Modes Supported by the CMX882
With Rx Voice
Processing1 or
Audio Tone
generation
Sub-Audio
All combinations of:
DCS
Inverted DCS
CTCSS
Voice band signalling
Any one of A - E:
A None
B 1200bps FFSK/MSK
C 2400bps FFSK/MSK
D 1200 & 2400 bps FFSK/MSK
E XTCSS3
With Rx Voice
Processing2
Sub-Audio
All combinations of:
DCS
Inverted DCS
CTCSS
Voice band signalling
One of A, B or E:
A None
B 1200bps FFSK/MSK
E XTCSS3
No Voice
Processing or
Audio Tone
generation
Sub-Audio
All combinations of:
DCS
Inverted DCS
CTCSS
Voice band signalling
All combinations of:
XTCSS3
1200bps FFSK/MSK
2400bps FFSK/MSK
1 Including optional de-emphasis and companding, but excluding voice scrambling
2 Including voice scrambling
3 XTCSS or In-band tone signalling
By disabling all the decoding modes, the device can be configured to receive voice only signals with no
decoding of the voice band, CTCSS or DCS signalling. This will result in reception of all signals as if
they are voice. In this case it is up to the user/host µC to respond appropriately to incoming signals.
The CMX882 operates in half duplex, so whilst in receive mode the transmit path (microphone input and
modulator output amplifiers) can be disabled and powered down if required. The AUDIO output signal
level is equalised (to VBIAS) before switching between the audio port and the modulator ports, to minimise
unwanted audible transients. The Off/Power-save level of the modulator outputs is the same as the
VBIAS pin, so the audio output level must also be at this level before switching.
2004 CML Microsystems Plc
17
D/882/7
 

Share Link: 

datasheetbank.com [ Privacy Policy ] [ Request Datasheet ] [ Contact Us ]