datasheetbank_Logo    Integrated circuits, Transistor, Semiconductors Search and Datasheet PDF Download Site
Part Name :

R1120N371B-TL View Datasheet(PDF) - RICOH Co.,Ltd.

Part NameR1120N371B-TL Ricoh
RICOH Co.,Ltd. Ricoh
DescriptionLOW NOISE 150mA L.D.O REGULATOR


R1120N371B-TL Datasheet PDF : 24 Pages
First Prev 21 22 23 24
R1120N
APPLICATION HINTS
When using these ICs, be sure to take care of following points :
• In these ICs, phase compensation is made for securing stable operation even if the load current is varied.
For this purpose, be sure to use a capacitor COUT with good frequency characteristics and ESR (Equivalent
Series Resistance) of which is in the range described as follows :
The relations between IOUT (Output Current) and ESR of Output Capacitor are shown below. The
conditions when the white noise level is under 40µV (Avg.) are marked as the hatched area in the graph.
(note : When the additional ceramic capacitors are connected to the Output Pin with Output capacitor for
phase compensation, there are possibilities that the operation will be unstable. Because of this, test these
ICs with as same external components as ones to be used on the PCB.)
< measuring conditions >
VIN=4V
Freqency band : 10Hz to 1MHz
Temperature : 25˚C
• Make VDD and GND line sufficient. When the impedance of these is high, there is a case to pick up the noise or
not to work correctly.
• Connect the capacitor with a capacitance of 1µF or more between VDD and GND as close as possible.
• Set external components, especially Output Capacitor, as close as possible to the ICs and make wiring
shortest.
Ceramic Capacitor 4.7µF
100
Ceramic Capacitor 6.8µF
100
10
10
1
1
0.1
0
50
80
150
Output Current IOUT(mA)
Ceramic Capacitor 10µF
100
0.1
0
50
80
150
Output Current IOUT(mA)
• Measuring Circuit for white noise ; R1120N301B
10
1
0.1
0
VIN
50
80
150
Output Current IOUT(mA)
4 CE
VOUT 1
R1120N301B
3 VIN GND
2
Ceramic
Capacitor1µF
Ceramic
Capacitor
ESR
IOUT
S.A.
Spectrum
Analyzer
18
Direct download click here

OUTLINE
The R1120N Series are voltage regulator ICs with high output voltage accuracy, lowest supply current, low ON Resistance and high Ripple Rejection by CMOS process. Each of these voltage regulator ICs consists of a voltage reference unit, an error amplifier, resistors, a current limit circuit and a chip enable circuit.
These ICs perform with low dropout voltage and a chip enable function.
The Dynamic Response to line and load is fast, so these ICs are very suitable for the power supply for handheld communi cation equipment.
The output voltage of these ICs is fixed with high accuracy.
Since the package for these ICs are SOT-23-5(Mini-mold)package, high density mounting of the ICs on boards is possible.

FEATURES
• Ultra-Low Supply Current.....................TYP. 35µA
• Standby Current.....................................TYP. 0.1µA
• Dropout Voltage.....................................TYP. 0.2V (IOUT=100mA)
• High Ripple Rejection............................TYP. 70dB (f=1kHz)
• High Accuracy Output Voltage ............±2.0%
• Low Temperature-Drift Coefficient of
   Output Voltage .......................................TYP. ±100ppm/˚C
• Excellent Line Regulation.....................TYP. 0.05%/V
• Pinout.......................................................Similar to the TK112
• Small Package.........................................SOT-23-5 (Mini-mold)

APPLICATIONS
• Power source for portable communication tools, cameras and VCRs.
• Power source for battery-powered equipment.
• Power source for domestic appliances.

Share Link : Ricoh

@ 2014 - 2018  [ Home ] [ Privacy Policy ] [ Request Datasheet ] [ Contact Us ]