datasheetbank_Logo
Integrated circuits, Transistor, Semiconductors Search and Datasheet PDF Download Site

D101EHI View Datasheet(PDF) - MicroPower Direct, LLC

Part Name
Description
View to exact match
D101EHI Datasheet PDF : 2 Pages
1 2
Model Selection Guide
Model
Number
Input
Voltage (VDC)
Current (mA)
Nominal Range Full-Load No-Load
Voltage
(VDC)
Output
Current Current
(mA, Max) (mA, Min)
Efficiency
(%, Typ)
Fuse Rating
Slow-Blow
(mA)
D101EHI
D102EHI
D103EHI
D104EHI
D105EHI
D106EHI
D107EHI
D108EHI
D111EHI
D112EHI
D113EHI
D114EHI
D115EHI
D116EHI
D117EHI
D118EHI
5
4.5 - 5.5
286
5
4.5 - 5.5
286
5
4.5 - 5.5
278
5
4.5 - 5.5
278
5
4.5 - 5.5
277
5
4.5 - 5.5
277
5
4.5 - 5.5
267
5
4.5 - 5.5
267
12
10.8 - 13.2
113
12
10.8 - 13.2
113
12
10.8 - 13.2
110
12
10.8 - 13.2
110
12
10.8 - 13.2
111
12
10.8 - 13.2
111
12
10.8 - 13.2
107
12
10.8 - 13.2
107
60
5.0
200
20.0
72
60
9.0
111
12.0
72
60
12.0
84
9.0
75
60
15.0
67
7.0
75
60
±5.0
±100
±10.0
72
60
±9.0
±56
±6.0
72
60
±12.0
±42
±5.0
75
60
±15.0
±33
±4.0
75
40
5.0
200
20.0
74
40
9.0
111
12.0
74
40
12.0
84
9.0
76
40
15.0
67
7.0
76
40
±5.0
±100
±10.0
75
40
±9.0
±56
±6.0
75
40
±12.0
±42
±5.0
78
40
±15.0
±33
±4.0
78
1,000
1,000
1,000
1,000
1,000
1,000
1,000
1,000
250
250
250
250
250
250
250
250
Notes:
1. Output load regulation is specified for a load change of 10% to
100%.
2. These units should not be operated with a load under 10% of full
load. Operation at no-load may cause damage to the unit.
3. These converters will operate without external components.
However, when measuring output ripple, it is recommended that
an external ceramic
capacitor be placed
from the +Vout pin
Vin
Input
Capacitor
Vout
Output
Capacitor
to the -Vout pin for 5 VDC 4.7 µF 5 VDC 4.7 µF
single output units 12 VDC
and from each out-
put to common for
dual output units. An
2.2 µF
9 VDC 2.2 µF
12 VDC 1.0 µF
15 VDC 0.47 µF
input capacitor will enhance stability over temperature and input
line variations. Recommended capacitor values are given in the
table above.
For applications requiring very low output noise levels, a simple Pi
filter should be effective. Component values would depend upon
the application, but capacitor values of 4.7 µF and inductor
values of 10 µH are often sufficient.
4. Dual output units may be connected to provide a 10V, 18V, 24V
or 30 VDC output. To do this, connect the load across the positive
(+Vout) and negative (-Vout) outputs and float the output com-
mon
5. It is recommended that a fuse be used on the input of a power
supply for protection. See the Model Selection table above for the
correct rating.
Derating Curve
Mechanical Dimensions
Pin Connections
Pin Single Dual
1
+Vin
+Vin
2
-Vin
-Vin
5
-Vout -Vout
6
No Pin Common
7
+Vout +Vout
Mechanical Notes:
All dimensions are typical in inches (mm)
Tolerance x.xx = ±0.01 (±0.25)
MicroPower Direct
www.micropowerdirect.com
292 Page Street Ste D Stoughton, MA 02072 TEL: (781) 344-8226 FAX: (781) 344-8481 E-Mail: sales@micropowerdirect.com
 

Share Link: 

datasheetbank.com [ Privacy Policy ] [ Request Datasheet ] [ Contact Us ]