datasheetbank_Logo    Integrated circuits, Transistor, Semiconductors Search and Datasheet PDF Download Site
Part Name :

TPA3002D2 View Datasheet(PDF) - Texas Instruments

Part NameTPA3002D2 TI
Texas Instruments TI
Description9-W STEREO CLASS-D AUDIO POWER AMPLFIER WITH DC VOLUME CONTROL
TPA3002D2 Datasheet PDF : 41 Pages
First Prev 21 22 23 24 25 26 27 28 29 30 Next Last
TPA3002D2
SLOS402C − DECEMBER 2002 − REVISED JANUARY 2004
THERMAL RESISTANCE
vs
THERMAL VIA QUANTITY 2-LAYER PCB
25
www.ti.com
24
23
22
21
20
4
6
8
10
12
14
16
Thermal Via Quantity (13 Mil Diameter)
Figure 39. Thermal Resistance
BASIC MEASUREMENT SYSTEM
This application note focuses on methods that use the basic equipment listed below:
D Audio analyzer or spectrum analyzer
D Digital multimeter (DMM)
D Oscilloscope
D Twisted pair wires
D Signal generator
D Power resistor(s)
D Linear regulated power supply
D Filter components
D EVM or other complete audio circuit
Figure 40 shows the block diagrams of basic measurement systems for class-AB and class-D amplifiers. A sine
wave is normally used as the input signal since it consists of the fundamental frequency only (no other
harmonics are present). An analyzer is then connected to the APA output to measure the voltage output. The
analyzer must be capable of measuring the entire audio bandwidth. A regulated dc power supply is used to
reduce the noise and distortion injected into the APA through the power pins. A System Two audio measurement
system (AP-II) (Reference 1) by Audio Precision includes the signal generator and analyzer in one package.
The generator output and amplifier input must be ac-coupled. However, the EVMs already have the ac-coupling
capacitors, (CIN), so no additional coupling is required. The generator output impedance should be low to avoid
attenuating the test signal, and is important since the input resistance of APAs is not very high (about 10 k).
Conversely the analyzer-input impedance should be high. The output impedance, ROUT, of the APA is normally
in the hundreds of milliohms and can be ignored for all but the power-related calculations.
Figure 40(a) shows a class-AB amplifier system. They take an analog signal input and produce an analog signal
output. These amplifier circuits can be directly connected to the AP-II or other analyzer input.
This is not true of the class-D amplifier system shown in Figure 40(b), which requires low pass filters in most
cases in order to measure the audio output waveforms. This is because it takes an analog input signal and
converts it into a pulse-width modulated (PWM) output signal that is not accurately processed by some
analyzers.
30
Direct download click here
 

DESCRIPTION
The TPA3002D2 is a 9-W (per channel) efficient, Class-D audio amplifier for driving bridged-tied stereo speakers. The TPA3002D2 can drive stereo speakers as low as 8 Ω. The high efficiency of the TPA3002D2 eliminates the need for external heatsinks when playing music.
Stereo speaker volume is controlled with a dc voltage applied to the volume control terminal offering a range of gain from –40 dB to 36 dB. Line outputs, for driving external headphone amplifier inputs, are also dc voltage controlled with a range of gain from –56 dB to 20 dB.
An integrated 5-V regulated supply is provided for powering an external headphone amplifier.

FEATURES
● 9-W/Ch Into an 8-Ω Load From 12-V Supply
● Efficient, Class-D Operation Eliminates
   Heatsinks and Reduces Power Supply
   Requirements
● 32-Step DC Volume Control From −40 dB to 36 dB
● Line Outputs For External Headphone
   Amplifier With Volume Control
● Regulated 5-V Supply Output for Powering TPA6110A2
● Space-Saving, Thermally-Enhanced PowerPAD™ Packaging
● Thermal and Short-Circuit Protection

APPLICATIONS
● LCD Monitors and TVs
● Powered Speakers

Share Link : TI
@ 2014 - 2018  [ Home ] [ Privacy Policy ] [ Request Datasheet ] [ Contact Us ]