PKD01EP View Datasheet(PDF) - Analog Devices
Part Name
Description
View to exact match
PKD01EP Datasheet PDF : 18 Pages
| |||
PKD01
ELECTRICAL CHARACTERISTICS (@ VS = ؎15 V, CH = 1000 pF, –55؇C ≤ TA ≤ +125؇C for PKD01AY, –25؇C ≤ TA ≤ +85؇C for
PKD01EY, PKD01FY and 0؇C ≤ TA ≤ +70؇C for PKD01EP, PKD01FP, unless otherwise noted.)
Parameter
Symbol Conditions
PKD01A/E
PKD01F
Min Typ Max Min Typ Max Unit
“gm” AMPLIFIERS A, B
Zero-Scale Error
Input Offset Voltage
Average Input Offset Drift1
VZS
VOS
TCVOS
Input Bias Current
IB
Input Offset Current
IOS
Voltage Gain
AV
Common-Mode Rejection Ratio CMRR
Power Supply Rejection Ratio
PSRR
Input Voltage Range1
VCM
Slew Rate
SR
Acquisition Time to 0.1% Accuracy1 tAQ
RL = 10 kΩ, VO = ± 10 V
–10 V ≤ VCM ≤ +10 V
± 9 V ≤ VS ≤ ± 18 V
20 V Step, AVCL = +1
47
6 12
36
5 10
–9 –24
–9 –24
160 250
160 500
30 100
30 150
7.5 9
59
74 82
72 80
80 90
70 90
± 10 ± 11
± 10 ± 11
0.4
0.4
60
60
mV
mV
µV/°C
nA
nA
V/mV
dB
dB
V
V/µs
µs
COMPARATOR
Input Offset Voltage
Average Input Offset Drift1
Input Bias Current
Input Offset Current
Voltage Gain
Common-Mode Rejection Ratio
Power Supply Rejection Ratio
Input Voltage Range1
Low Output Voltage
OFF Output Leakage Current
Output Short-Circuit Current
Response Time
VOS
TCVOS
IB
IOS
AV
CMRR
PSRR
VCM
VOL
IL
ISC
tS
2 kΩ Pull-Up Resistor to 5 V
–10 V ≤ VCM ≤ +10 V
± 9 V ≤ VS ≤ ± 18 V
ISINK ≤ 5 mA, Logic GND = 0 V
VOUT = 5 V
VOUT = 5 V
5 mV Overdrive, 2 kΩ Pull-Up
Resistor to 5 V
2 2.5
–4 –6
1000 2000
100 600
4 6.5
2.5
80 100
80
72 82
72
± 11
± 11
–0.2 +0.15 +0.4 –0.2
25 100
6 10 45 6
200
25
–4 –6
1100 2000
100 600
6.5
92
86
+0.15 +0.4
100 180
10 45
200
mV
µV/°C
nA
nA
V/mV
dB
dB
V
V
µA
mA
ns
DIGITAL INPUTS – RST, DET2
Logic “1” Input Voltage
VH
Logic “0” Input Voltage
VL
Logic “1” Input Current
IINH
Logic “0” Input Current
IINL
VH = 3.5 V
VL = 0.4 V
2
2
0.8
0.02 1
2.5 15
V
0.8 V
0.02 1
µA
2.5 15 µA
MISCELLANEOUS
Droop Rate3
Output Voltage Swing
Amplifier C
Short-Circuit Current
Amplifier C
Switch Aperture Time
Slew Rate: Amplifier C
Power Supply Current
VDR
TJ = Max Operating Temp.
TA = Max Operating Temp.
DET = 1
1.2 10
2.4 20
3 15 mV/ms
6 20 mV/ms
VOP
RL = 2.5 kΩ
± 11 ± 12
± 10.5 ± 12
V
ISC
tAP
SR
RL = 2.5 kΩ
ISY
No Load
6 12 40 6 12 40 mA
75
75
ns
2
2
V/µs
5.5 8
6.5 10 mA
NOTES
1Guaranteed by design.
2DET = 1, RST = 0.
3Due to limited production test times, the droop current corresponds to junction temperature (T J). The droop current vs. time (after power-on) curve clarifies this
point. Since most devices (in use) are on for more than 1 second, ADI specifies droop rate for ambient temperature (T A) also. The warmed-up (TA) droop current
specification is correlated to the junction temperature (TJ) value. ADI has a droop current cancellation circuit that minimizes droop current at high temperature.
Ambient (TA) temperature specifications are not subject to production testing.
Specifications subject to change without notice.
REV. A
–3–
|
|
Share Link: 