DS2482-800 View Datasheet(PDF) - Dallas Semiconductor -> Maxim Integrated

Part Name

Description

View to exact match

DS2482-800

Eight-Channel 1-Wire Master

Dallas Semiconductor -> Maxim Integrated 

Figure 4. Low-Impedance Pullup Timing

DS2482-800: Eight-Channel 1-Wire Master

Last bit of 1-Wire Write Byte or 1-Wire Single Bit Function

Vcc

Write 1

Edges with

active pull-up

Write 0

0V

tSLOT

Next

Time

Slot

Pull-up

DS2482 Pull-down

DS2482 Low Impedance Pull-up

1-Wire Speed (1WS)

The 1WS bit determines the timing of any 1-Wire communication generated by the DS2482. All 1-Wire slave

devices support standard speed (1WS = 0), where the transfer of a single bit (tSLOT in Figure 4) is completed within

65µs. Many 1-Wire device can also communicate at a higher data rate, called Overdrive speed. To change from

standard to Overdrive speed, a 1-Wire device needs to receive an Overdrive Skip ROM or Overdrive Match ROM

command, as explained in the device data sheets. The change in speed occurs immediately after the 1-Wire device

has received the speed-changing command code. The DS2482 must take part in this speed change to stay

synchronized. This is accomplished by writing to the Configuration Register with the 1WS bit being 1 immediately

after the 1-Wire Byte command that changes the speed of a 1-Wire device. Writing to the Configuration Register

with the 1WS bit being 0 followed by a 1-Wire Reset command changes the DS2482 and any 1-Wire devices on

the active 1-Wire line back to standard speed.

Status Register

The read-only Status Register is the general means for the DS2482 to report bit-type data from the 1-Wire side, 1-

Wire busy status and its own reset status to the host processor. All 1-Wire communication commands and the

Device Reset command position the read pointer at the Status Register for the host processor to read with minimal

protocol overhead. Status information is updated during the execution of certain commands only. Details are given

in the description of the various status bits below.

Status Register Bit Assignment

bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0

DIR TSB SBR RST LL

SD PPD 1WB

1-Wire Busy (1WB)

The 1WB bit reports to the host processor whether the 1-Wire line is busy. During 1-Wire communication 1WB is 1;

once the command is completed, 1WB returns to its default 0. Details on when 1WB changes state and for how

long it remains at 1 are found in the Function Commands section.

Presence Pulse Detect (PPD)

The PPD bit is updated with every 1-Wire Reset command. If the DS2482 detects a presence pulse from a 1-Wire

device at tMSP during the Presence Detect cycle, the PPD bit will be set to 1. This bit will return to its default 0 if

there is no presence pulse or if the 1-Wire line is shorted during a subsequent 1-Wire Reset command.

Short Detected (SD)

The SD bit is updated with every 1-Wire Reset command. If the DS2482 detects a logic 0 on the 1-Wire line at tSI

during the Presence Detect cycle, the SD bit will be set to 1. This bit will return to its default 0 with a subsequent 1-

Wire Reset command provided that the short has been removed. If SD is 1, PPD will be 0. The DS2482 cannot

distinguish between a short and a DS1994 or DS2404 signaling a 1-Wire interrupt. For this reason, if a

DS2404/DS1994 is used in the application, the interrupt function must be disabled. The interrupt signaling is

explained in the respective device data sheets.

8 of 22

Share Link: