A29800AUG-55UF View Datasheet(PDF) - AMIC Technology
Part Name
Description
View to exact match
A29800AUG-55UF
AMIC Technology
A29800AUG-55UF Datasheet PDF : 40 Pages
| |||
A29800A Series
Absolute Maximum Ratings*
Storage Temperature Plastic Packages. . . -65°C to + 150°C
Ambient Temperature with Power Applied. -55°C to + 125°C
Voltage with Respect to Ground
VCC (Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . -2.0V to +6.5V
A9, OE & RESET (Note 2) . . . . . . . . .. . . . -2.0V to +11.5V
All other pins (Note 1) . . . . . . . . . . . . . . . … . . -2.0V to 6.5V
Output Short Circuit Current (Note 3) . . . . . . . …. . 200mA
Notes:
1. Minimum DC voltage on input or I/O pins is -0.5V. During
voltage transitions, input or I/O pins may undershoot VSS
to -2.0V for periods of up to 20ns. Maximum DC voltage
on input and I/O pins is VCC +0.5V. During voltage
transitions, input or I/O pins may overshoot to VCC +1.5V
for periods up to 20ns.
2. Minimum DC input voltage on A9, OE and RESET is -
0.5V. During voltage transitions, A9, OE and RESET
may overshoot VSS to -2.0V for periods of up to 20ns.
Maximum DC input voltage on A9 is +11.5V which may
overshoot to 12.5V for periods up to 20ns.
3. No more than one output is shorted at a time. Duration of
the short circuit should not be greater than one second.
Device Bus Operations
This section describes the requirements and use of the
device bus operations, which are initiated through the
internal command register. The command register itself does
not occupy any addressable memory location. The register is
composed of latches that store the commands, along with
the address and data information needed to execute the
*Comments
Stresses above those listed under "Absolute Maximum
Ratings" may cause permanent damage to this device.
These are stress ratings only. Functional operation of
this device at these or any other conditions above
those indicated in the operational sections of these
specification is not implied or intended. Exposure to
the absolute maximum rating conditions for extended periods
may affect device reliability.
Operating Ranges
Commercial Devices
Ambient Temperature (TA) …………………….. 0°C to +70°C
Extended Range Devices
Ambient Temperature (TA) …………………… -40°C to +85°C
VCC Supply Voltages
VCC for all devices ……………………………. +4.5V to +5.5V
Operating ranges define those limits between which the
functionally of the device is guaranteed.
command. The contents of the register serve as inputs to the
internal state machine. The state machine outputs dictate the
function of the device. The appropriate device bus operations
table lists the inputs and control levels required, and the
resulting output. The following subsections describe each of
these operations in further detail.
Table 1. A29800A Device Bus Operations
Operation
Read
Write
CMOS Standby
Output Disable
Hardware Reset
Sector Protect
(See Note 2)
Sector Unprotect
(See Note 2)
Temporary Sector
Unprotect
CE OE WE RESET
L
LH
H
A0 – A18
(Note 1)
AIN
I/O0 - I/O7
DOUT
L
HL
H
AIN
DIN
VCC ± X
0.3 V
L
H
X
X
L
H
L
H
X
X
X VCC ±
X
0.3 V
High-Z
H
H
X
High-Z
X
L
X
High-Z
L
VID
Sector Address,
DIN
A6=L, A1=H, A0=L
L
VID
Sector Address,
DIN
A6=H, A1=H, A0=L
X
VID
AIN
DIN
I/O8 - I/O15
BYTE =VIH
DOUT
DIN
High-Z
BYTE =VIL
I/O8~I/O14=High-Z
I/O15=A-1
I/O8~I/O14=High-Z
I/O15=A-1
High-Z
High-Z
High-Z
X
High-Z
High-Z
X
X
X
DIN
X
Legend:
L = Logic Low = VIL, H = Logic High = VIH, VID = 10.5 ± 1.0V, X = Don't Care, DIN = Data In, DOUT = Data Out, AIN = Address In
Notes:
1. Addresses are A18:A0 in word mode (BYTE=VIH), A18: A-1 in byte mode (BYTE=VIL).
2. See the “Sector Protection/Unprotection” section and Temporary Sector Unprotect for more information.
(August, 2014, Version 1.3)
5
AMIC Technology, Corp.
|
|
Share Link: