datasheetbank_Logo
Integrated circuits, Transistor, Semiconductors Search and Datasheet PDF Download Site

M29F800FB5AN6E2 View Datasheet(PDF) - Micron Technology

Part Name
Description
View to exact match
M29F800FB5AN6E2
Micron
Micron Technology Micron
M29F800FB5AN6E2 Datasheet PDF : 55 Pages
First Prev 21 22 23 24 25 26 27 28 29 30 Next Last
M29FxxxFT/B
Command Interface
10. CFI Query: Command is valid when device is ready to read array data or when device is
in auto select mode.
8-Bit Mode Commands
Table 6: 8-Bit Mode Commands (BYTE# = LOW)
Command
READ/RESET
AUTO SELECT
PROGRAM
UNLOCK BYPASS
UNLOCK BYPASS
PROGRAM
UNLOCK BYPASS
RESET
CHIP ERASE
BLOCK ERASE
ERASE SUSPEND
ERASE RESUME
READ CFI QUERY
1st
Length Addr Data
1
X
F0
3
AAA AA
3
AAA AA
4
AAA AA
3
AAA AA
2
X
A0
2nd
Addr Data
555 55
555 55
555 55
555 55
PA PD
WRITE Operations
3rd
4th
Addr Data Addr Data
X
F0
AAA 90
AAA A0 PA PD
AAA 20
5th
Addr Data
6th
Addr Data
2
X
90
X
00
6
AAA AA 555 55 AAA 80 AAA AA 555 55 AAA 10
6+ AAA AA 555 55 AAA 80 AAA AA 555 55 BA 30
1
X
B0
1
X
30
1
AA 98
Notes: 1. X = "Don’t Care;" PA = Program address; PD = Program data; BA = Any address in the
block. All values in the table are in hexadecimal.
2. Command interface: Only uses A-1, A[10;0], and DQ[7;0] to verify the commands;
A[19:11], DQ[14:8], and DQ15 are "Don’t Care." DQ15/A-1 is A-1 when BYTE is LOW or
DQ15 when BYTE is HIGH.
3. Read/Reset: After a READ/RESET command, read the memory as normal until another
command is issued.
4. Auto Select: After an AUTO SELECT command, read manufacturer ID, device ID, or
block protection status.
5. Program, Unlock Bypass Program, Chip Erase, Block Erase: After issuing these
commands, read the status register until the program/erase controller completes and
the device returns to read mode. Add additional blocks during a BLOCK ERASE com-
mand with additional bus WRITE operations until the timeout bit is set.
6. Unlock Bypass: After the UNLOCK BYPASS command, issue an UNLOCK BYPASS PRO-
GRAM or UNLOCK BYPASS RESET command.
7. Unlock Bypass Reset: After the UNLOCK BYPASS RESET command, read the memory as
normal until another command is issued.
8. Erase Suspend: After the ERASE SUSPEND command, read non-erasing blocks as nor-
mal. Issue AUTO SELECT and PROGRAM commands on non-erasing blocks as normal.
9. Erase Resume: After the ERASE RESUME command, the suspended ERASE operation re-
sumes. Read the status register until the program/erase controller completes and the de-
vice returns to read mode.
10. CFI Query: Command is valid when device is ready to read array data or when device is
in auto select mode.
PDF: 09005aef845656da
m29fxxxf/t_2mb-16mb.pdf - Rev. B 2/14 EN
30
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2013 Micron Technology, Inc. All rights reserved.
 

Share Link: 

datasheetbank.com [ Privacy Policy ] [ Request Datasheet ] [ Contact Us ]