MC100LVEL56DW(2006) View Datasheet(PDF) - ON Semiconductor
Part Name
Description
View to exact match
MC100LVEL56DW Datasheet PDF : 7 Pages
| |||
MC100LVEL56
Table 4. MAXIMUM RATINGS
Symbol
Parameter
Condition 1
Condition 2
Rating
Unit
VCC
PECL Mode Power Supply
VEE
NECL Mode Power Supply
VI
PECL Mode Input Voltage
NECL Mode Input Voltage
Iout
Output Current
VEE = 0 V
VCC = 0 V
VEE = 0 V
VCC = 0 V
Continuous
Surge
VI VCC
VI VEE
8 to 0
V
−8 to 0
V
6 to 0
V
−6 to 0
V
50
mA
100
mA
IBB
VBB Sink/Source
TA
Operating Temperature Range
Tstg
Storage Temperature Range
qJA
Thermal Resistance (Junction−to−Ambient) 0 lfpm
500 lfpm
SO−20 WB
SO−20 WB
± 0.5
−40 to +85
−65 to +150
90
60
mA
°C
°C
°C/W
°C/W
qJC
Thermal Resistance (Junction−to−Case) Standard Board
SO−20 WB
Tsol
Wave Solder
Pb t2 to 3 sec @ 248°C
Pb−Free t2 to 3 sec @ 260°C
30 to 35
265
265
°C/W
°C
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
Table 5. LVPECL DC CHARACTERISTICS VCC = 3.3 V; VEE = 0.0 V (Note 2)
−40°C
25°C
85°C
Symbol
Characteristic
Min Typ Max Min Typ Max Min Typ Max Unit
IEE
VOH
VOL
VIH
VIL
VBB
VIHCMR
IIH
IIL
Power Supply Current
20
24
20
24
20
24
mA
Output HIGH Voltage (Note 3)
2215 2295 2420 2275 2345 2420 2275 2345 2420 mV
Output LOW Voltage (Note 3)
1470 1605 1745 1490 1595 1680 1490 1595 1680 mV
Input HIGH Voltage (Single−Ended)
2135
2420 2135
2420 2135
2420 mV
Input LOW Voltage (Single−Ended)
1490
1825 1490
1825 1490
1825 mV
Output Voltage Reference
1.92
2.04 1.92
2.04 1.92
2.04 V
Input HIGH Voltage Common Mode
Range (Differential) (Note 4)
Vpp < 500 mV 1.3
Vpp y 500 mV 1.5
Input HIGH Current
2.9 1.2
2.9 1.4
150
2.9 1.2
2.9 1.4
150
2.9
V
2.9
V
150 mA
Input LOW Current
Dn 0.5
0.5
0.5
mA
Dn −600
−600
−600
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
2. Input and output parameters vary 1:1 with VCC. VEE can vary ±0.3 V.
3. Outputs are terminated through a 50 W resistor to VCC − 2.0 V.
4. VIHCMR min varies 1:1 with VEE, max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input
signal. Normal operation is obtained if the HIGH level falls within the specified range and the peak-to-peak voltage lies between VPP(min)
and 1 V.
http://onsemi.com
3
|
|
Share Link: 