datasheetbank_Logo
Integrated circuits, Transistor, Semiconductors Search and Datasheet PDF Download Site

M12L64164A-5BIG View Datasheet(PDF) - [Elite Semiconductor Memory Technology Inc.

Part Name
Description
View to exact match
M12L64164A-5BIG
ESMT
[Elite Semiconductor Memory Technology Inc. ESMT
M12L64164A-5BIG Datasheet PDF : 45 Pages
1 2 3 4 5 6 7 8 9 10 Next Last
ESMT
M12L64164A
Operation Temperature Condition -40°C~85°C
SIMPLIFIED TRUTH TABLE
Register
COMMAND
Mode Register set
CKEn-1 CKEn CS RAS CAS
H
X LL L
WE
DQM
A13
A12
A10/AP
A11
A9~A0
LX
OP CODE
Note
1,2
Auto Refresh
H
3
H
LL L H X
X
Refresh
Self
Entry
L
3
Refresh
LH H H X
3
Exit
L
H
X
HX X X X
3
Bank Active & Row Addr.
H
X LL H H X V
Row Address
Read &
Auto Precharge Disable
H
Column Address Auto Precharge Enable
X LH L H X V
L Column 4
Address
H (A0~A7) 4,5
Write &
Auto Precharge Disable
H
Column Address Auto Precharge Enable
X LH L L X V
L Column 4
Address
H (A0~A7) 4,5
Burst Stop
H
X LH H L X
X
6
Precharge
Bank Selection
All Banks
V
L
H
X LL H L X
X
X
H
Clock Suspend or
Active Power Down
HX X X
Entry
H
L
X
LV V V
X
Exit
L
H XX X X X
HX X X
Entry
H
L
X
Precharge Power Down Mode
LH H H
X
HX X X
Exit
L
H
X
LV V V
DQM
No Operating Command
H
X
V
X
7
HX X X
H
X
X
X
LH H H
Note :
(V = Valid , X = Don’t Care. H = Logic High , L = Logic Low )
1.OP Code : Operating Code
A0~A11 & A13~A12 : Program keys. (@ MRS)
2.MRS can be issued only at all banks precharge state.
A new command can be issued after 2 CLK cycles of MRS.
3.Auto refresh functions are as same as CBR refresh of DRAM.
The automatical precharge without row precharge of command is meant by “Auto”.
Auto/self refresh can be issued only at all banks idle state.
4.A13~A12 : Bank select addresses.
If both A13 and A12 are “Low” at read ,write , row active and precharge ,bank A is selected.
If both A13 is “Low” and A12 is “High” at read ,write , row active and precharge ,bank B is selected.
If both A13 is “High” and A12 is “Low” at read ,write , row active and precharge ,bank C is selected.
If both A13 and A12 are “High” at read ,write , row active and precharge ,bank D is selected
If A10/AP is “High” at row precharge , A13 and A12 is ignored and all banks are selected.
5.During burst read or write with auto precharge. new read/write command can not be issued.
Another bank read/write command can be issued after the end of burst.
New row active of the associated bank can be issued at tRP after the end of burst.
6.Burst stop command is valid at every burst length.
7.DQM sampled at positive going edge of a CLK and masks the data-in at the very CLK (write DQM latency is 0), but
makes Hi-Z state the data-out of 2 CLK cycles after.(Read DQM latency is 2)
Elite Semiconductor Memory Technology Inc.
Publication Date: Dec. 2007
Revision: 1.2
8/45
 

Share Link: 

datasheetbank.com [ Privacy Policy ] [ Request Datasheet ] [ Contact Us ]