datasheetbank_Logo    Integrated circuits, Transistor, Semiconductors Search and Datasheet PDF Download Site
Part Name :

HI-8581CJT-10 View Datasheet(PDF) - Holt Integrated Circuits

Part NameHI-8581CJT-10 Holt
Holt Integrated Circuits Holt
DescriptionARINC 429 Transmitter with Line Driver and Dual Receivers
HI-8581CJT-10 Datasheet PDF : 15 Pages
1 2 3 4 5 6 7 8 9 10 Next Last
HI-8581, HI-8589
FUNCTIONAL DESCRIPTION (cont.)
LINE DRIVER OPERATION
The line driver in the HI-8581 and HI-8589 is designed to directly
drive the ARINC 429 bus. The two ARINC outputs (TXA(OUT) and
TXB(OUT)) provide a differential voltage to produce a +10 volt
One, a -10 volt Zero, and a 0 volt Null. Setting Control Register bit
13 to zero causes a slope of 1.5 ms on the ARINC outputs. A one in
Control Register bit 13 causes a slope of 10 ms. Timing is set by on-
chip resistor and capacitor and tested to be within ARINC require-
ments. No additional hardware is required to control the slope. The
HI-8581 has 37.5 ohms whereas the HI-8589 has 10 ohms in
series with each line driver output. The HI-8589 is for applications
where additional external series resistance is required, such as
lightning protection.
REPEATER OPERATION
Repeater mode of operation allows a data word that has been
received by the HI-8581 or HI-8589 to be placed directly into its
FIFO for transmission. Repeater operation is similar to normal
receiver operation. In normal operation, either byte of a received
data word may be read from the receiver latches first by use of SEL
input. During repeater operation however, the lower byte of the
data word must be read first. This is necessary because, as the
data is being read, it is also being loaded into the FIFO and the
transmitter FIFO is always loaded with the lower byte of the data
word first. Signal flow for repeater operation is shown in the
Timing Diagrams section.
TIMING DIAGRAMS
HI-8581-10 and HI-8589-10
The “-10” versions of the HI-8581 and HI-8589 products require a
10 Kohm resistor to be placed in series with each ARINC input
without affecting the ARINC input thresholds. This option is
especially useful in applications where external lightning
protection is required.
Each ARINC input pin must be connected to the ARINC bus
through a 10 Kohm resistor in order for the chip to properly detect
the correct ARINC levels. The typical 10 volt differential signal is
translated and input to a window comparator and latch. The
comparator levels are set so that with the external 10 Kohm
resistors, they are just below the standard 6.5 volt minimum
ARINC data threshold and just above the 2.5 volt maximum
ARINC null threshold.
Please refer to the Holt AN-300 Application Note for additional
information and recommendations on lightning protection of Holt
line drivers and line receivers.
POWER SUPPLY SEQUENCING
The power supplies should be controlled to prevent large currents
during supply turn-on and turn-off. The recommended sequence
is V+ followed by Vcc, always ensuring that V+ is the most
positive supply. The V- supply is not critical and can be asserted
at any time.
MASTER RESET (MR)
On a Master Reset data transmission and reception are
immediately terminated, all three FIFOs are cleared as are the
FIFO flags at the device pins and in the Status Register. The
Control Register is not affected by a Master Reset.
TXA(OUT)
TXB(OUT)
DATA RATE - EXAMPLE PATTERN
ARINC BIT
DATA
NULL
BIT 30
DATA
NULL
BIT 31
DATA
NULL
BIT 32
WORD GAP
BIT 1
NEXT WORD
LOADING CONTROL WORD
DATA BUS
CWSTR
VALID
tCWSET
tCWHLD
tCWSTR
HOLT INTEGRATED CIRCUITS
6
Direct download click here
 

GENERAL DESCRIPTION
The HI-8581 and HI-8589 from Holt Integrated Circuits are silicon gate CMOS devices for interfacing a 16-bit parallel data bus directly to the ARINC 429 serial bus. Both devices provide two receivers, an independent transmitter and line driver capability in a single package. The receiver input circuitry and logic are designed to meet the ARINC 429 specifications for loading, level detection, timing, and protocol. The transmitter section provides the ARINC 429 communication protocol and the line driver circuits provide the ARINC 429 output levels.
The 16-bit parallel data bus exchanges the 32-bit ARINC data word in two steps when either loading the transmitter or interrogating the receivers. The data bus interfaces with CMOS and TTL.
The HI-8581 has 37.5 ohms in series with each line driver output. The HI-8589 provides the option to bypass most of the internal output resistance so that external series resistance may be added for lighting protection and still match the 75 ohm characteristic impedance of the ARINC bus.

FEATURES
• ARINC specification 429 compliant
• Direct receiver and transmitter interface to ARINC bus in a single device
• 16-Bit parallel data bus
• Timing control 10 times the data rate
• Selectable data clocks
• Receiver error rejection per ARINC 429 standard
• Automatic transmitter data timing
• Parity functions
• Low power
• Self test mode
• Industrial & extended temperature ranges

 

Share Link : Holt
@ 2014 - 2018  [ Home ] [ Privacy Policy ] [ Request Datasheet ] [ Contact Us ]