HI-8581CJT-10 View Datasheet(PDF) - Holt Integrated Circuits

Part Name

Description

View to exact match

HI-8581CJT-10

ARINC 429 Transmitter with Line Driver and Dual Receivers

Holt Integrated Circuits 

HI-8581, HI-8589

FUNCTIONAL DESCRIPTION (cont.)

TRANSMITTER

A block diagram of the transmitter section is shown in Figure 3.

FIFO OPERATION

The FIFO is loaded sequentially by first pulsing PL1 to load byte 1

and then PL2 to load byte 2. The control logic automatically loads

the 31 bit word in the next available position of the FIFO. If TX/R,

the transmitter ready flag is high (FIFO empty), then 8 words,

each 31 bits long, may be loaded. If TX/R is low, then only the

available positions may be loaded. If all 8 positions are full, the

FIFO ignores further attempts to load data.

DATA TRANSMISSION

When ENTX goes high, enabling transmission, the FIFO

positions are incremented with the top register loading into the

data transmission shift register. Within 2.5 data clocks the first

data bit appears at either TXA(OUT) or TXB(OUT). The 31 bits in

the data transmission shift register are presented sequentially to

the outputs in the ARINC 429 format with the following timing:

ARINC DATA BIT TIME

DATA BIT TIME

NULL BIT TIME

WORD GAP TIME

HIGH SPEED

10 Clocks

5 Clocks

5 Clocks

40 Clocks

LOW SPEED

80 Clocks

40 Clocks

40 Clocks

320 Clocks

The word counter detects when all loaded positions are

transmitted and sets the transmitter ready flag, TX/R, high.

TRANSMITTER PARITY

The parity generator counts the ONES in the 31-bit word. If the

BD12 control word bit is set low, the 32nd bit transmitted will

make parity odd. If the control bit is high, the parity is even.

SELF TEST

If the BD05 control word bit is set low, the digital outputs of the

transmitter are internally connected to the logic inputs of the

receivers, bypassing the analog bus interface circuitry. Data to

Receiver 1 is as transmitted and data to Receiver 2 is the

complement. All data transmitted during self test is also present

on the TXA(OUT) and TXB(OUT) line driver outputs.

SYSTEM OPERATION

The two receivers are independent of the transmitter. Therefore,

control of data exchanges is strictly at the option of the user. The

only restrictions are:

1. The received data may be overwritten if not retrieved

within one ARINC word cycle.

2. The FIFO can store 8 words maximum and ignores

attempts to load addition data if full.

3. Byte 1 of the transmitter data must be loaded first.

4. Either byte of the received data may be retrieved first.

Both bytes must be retrieved to clear the data ready flag.

5. After ENTX, transmission enable, goes high it cannot go

low until TX/R, transmitter ready flag, goes high. Otherwise,

one ARINC word is lost during transmission.

31 BIT PARALLEL

LOAD SHIFT REGISTER

BIT CLOCK

BIT BD12

PARITY

GENERATOR

DATA AND

NULL TIMER

SEQUENCER

LINE DRIVER

TXA(OUT)

TXB(OUT)

8 X 31 FIFO

WORD CLOCK

ADDRESS

LOAD

DATA BUS

FIGURE 3. TRANSMITTER BLOCK DIAGRAM

BIT

AND

WORD GAP

COUNTER

START

SEQUENCE

WORD COUNTER

AND

FIFO CONTROL

INCREMENT

WORD COUNT

FIFO

LOADING

SEQUENCER

DATA

CLOCK

DATA CLOCK

DIVIDER

CONTROL BIT

BD13

TX/R

ENTX

PL1

PL2

CLK

TX CLK

HOLT INTEGRATED CIRCUITS

5

Share Link: