K814P View Datasheet(PDF) - Vishay Semiconductors
Part Name
Description
View to exact match
K814P Datasheet PDF : 8 Pages
| |||
K814P/K824P/K844P
Vishay Semiconductors
Optocoupler, Phototransistor
Output, AC Input
ABSOLUTE MAXIMUM RATINGS (1)
PARAMETER
TEST CONDITION
SYMBOL
VALUE
UNIT
COUPLER
AC isolation test voltage (RMS)
Total power dissipation
Operating ambient temperature range
Storage temperature range
Soldering temperature (3)
t = 1.0 min
2 mm from case, t ≤ 10 s
VISO (2)
Ptot
Tamb
Tstg
Tsld
5000
250
- 40 to +100
- 55 to + 125
260
VRMS
mW
°C
°C
°C
Notes
(1) Tamb = 25 °C, unless otherwise specified.
Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. Functional operation of the device is not
implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute maximum
ratings for extended periods of the time can adversely affect reliability.
(2) Related to standard climate 23/50 DIN 50014.
(3) Refer to wave profile for soldering conditions for through hole devices.
ELECTRICAL CHARACTERISTICS
PARAMETER
TEST CONDITION
SYMBOL MIN.
TYP.
MAX.
UNIT
INPUT
Forward voltage
Reverse current
OUTPUT
IF = ± 50 mA
VF
VR = ± 6.0 V
IR
1.25
1.6
V
10
µA
Collector emitter voltage
Emitter collector voltage
Collector dark current
COUPLER
IC = 100 µA
VCEO
70
IE = 100 µA
VECO
7
VCE = 20 V, IF = 0, E = 0
ICEO
V
V
100
nA
Collector emitter saturation voltage
Cut-off frequency
Coupling capacitance
IF = ± 10 mA, IC = 1 mA
IF = ± 10 mA, VCE = 5 V,
RL = 100 Ω
f = 1 MHz
VCEsat
fc
Ck
0.3
V
100
kHz
0.3
pF
Note
Tamb = 25 °C, unless otherwise specified.
Minimum and maximum values are testing requirements. Typical values are characteristics of the device and are the result of engineering
evaluation. Typical values are for information only and are not part of the testing requirements.
CURRENT TRANSFER RATIO
PARAMETER
TEST CONDITION
IC/IF
VCE = 5 V, IF = ± 5 mA
PART
K814P
SYMBOL
CTR
MIN.
20
TYP.
MAX.
300
UNIT
%
SWITCHING CHARACTERISTICS
PARAMETER
TEST CONDITION
Delay time
Rise time
Fall time
Storage time
Turn-on time
Turn-off time
Turn-on time
Turn-off time
VS = 5 V, IC = 2 mA, RL = 100 Ω (see figure 1)
VS = 5 V, IC = 2 mA, RL = 100 Ω (see figure 1)
VS = 5 V, IC = 2 mA, RL = 100 Ω (see figure 1)
VS = 5 V, IC = 2 mA, RL = 100 Ω (see figure 1)
VS = 5 V, IC = 2 mA, RL = 100 Ω (see figure 1)
VS = 5 V, IC = 2 mA, RL = 100 Ω (see figure 1)
VS = 5 V, IC = 10 mA, RL = 1 kΩ (see figure 1)
VS = 5 V, IC = 10 mA, RL = 1 kΩ (see figure 1)
SYMBOL
td
tr
tf
ts
ton
toff
ton
toff
MIN.
TYP.
3.0
3.0
4.7
0.3
6.0
5.0
9.0
18.0
MAX.
UNIT
µs
µs
µs
µs
µs
µs
µs
µs
www.vishay.com
2
For technical questions, contact: optocoupler.answers@vishay.com
Document Number: 83523
Rev. 2.0, 09-Jan-08
|
|
Share Link: 