ST10F276R-6QR3 View Datasheet(PDF) - STMicroelectronics

Part Name

Description

View to exact match

ST10F276R-6QR3

16-bit MCU with MAC unit 832 Kbyte Flash memory and 68 Kbyte RAM

STMicroelectronics 

ST10F276E

Pin data

Table 1. Pin description (continued)

Symbol

Pin Type

Function

EA / VSTBY

99

P0L.0 -P0L.7, 100-107,

P0H.0

108,

P0H.1 - P0H.7 111-117

External access enable pin.

A low level applied to this pin during and after Reset forces the ST10F276E to

start the program from the external memory space. A high level forces

ST10F276E to start in the internal memory space. This pin is also used (when

Stand-by mode is entered, that is ST10F276E under reset and main VDD turned

off) to bias the 32 kHz oscillator amplifier circuit and to provide a reference

I voltage for the low-power embedded voltage regulator which generates the

internal 1.8V supply for the RTC module (when not disabled) and to retain data

inside the Stand-by portion of the XRAM (16 Kbyte).

It can range from 4.5 to 5.5V (6V for a reduced amount of time during the device

life, 4.0V when RTC and 32 kHz on-chip oscillator amplifier are turned off). In

running mode, this pin can be tied low during reset without affecting 32 kHz

oscillator, RTC and XRAM activities, since the presence of a stable VDD

guarantees the proper biasing of all those modules.

Two 8-bit bidirectional I/O ports P0L and P0H, bit-wise programmable for input or

output via direction bit. Programming an I/O pin as input forces the

corresponding output driver to high impedance state. The input threshold of

Port 0 is selectable (TTL or CMOS).

In case of an external bus configuration, PORT0 serves as the address (A) and

as the address / data (AD) bus in multiplexed bus modes and as the data (D) bus

in demultiplexed bus modes.

Demultiplexed bus modes

Data path width

I/O

P0L.0 – P0L.7:

8-bit

D0 – D7

P0H.0 – P0H.7: I/O

Multiplexed bus modes

16-bi

D0 - D7

D8 - D15

Data path width

P0L.0 – P0L.7:

P0H.0 – P0H.7:

8-bit

AD0 – AD7

A8 – A15

16-bi

AD0 - AD7

AD8 - AD15

118-125

128-135

P1L.0 - P1L.7

P1H.0 - P1H.7

132

133

134

135

Two 8-bit bidirectional I/O ports P1L and P1H, bit-wise programmable for input or

output via direction bit. Programming an I/O pin as input forces the

corresponding output driver to high impedance state. PORT1 is used as the 16-

bit address bus (A) in demultiplexed bus modes: if at least BUSCONx is

configured such the demultiplexed mode is selected, the pis of PORT1 are not

I/O available for general purpose I/O function. The input threshold of Port 1 is

selectable (TTL or CMOS).

The pins of P1L also serve as the additional (up to 8) analog input channels for

the A/D converter, where P1L.x equals ANy (Analog input channel y,

where y = x + 16). This additional function have higher priority on demultiplexed

bus function. The following PORT1 pins have alternate functions:

I P1H.4 CC24IO

CAPCOM2: CC24 capture input

I P1H.5 CC25IO

CAPCOM2: CC25 capture input

I P1H.6 CC26IO

CAPCOM2: CC26 capture input

I P1H.7 CC27IO

CAPCOM2: CC27 capture input

Doc ID 12303 Rev 3

21/235

Share Link: