datasheetbank_Logo    Integrated circuits, Transistor, Semiconductors Search and Datasheet PDF Download Site
Part Name :

W25Q80DVZPI View Datasheet(PDF) - Winbond

Part NameW25Q80DVZPI Winbond
Winbond Winbond
W25Q80DVZPI Datasheet PDF : 71 Pages
First Prev 51 52 53 54 55 56 57 58 59 60 Next Last
Erase Security Registers (44h)
The W25Q80DV offers three 256-byte Security Registers which can be erased and programmed
individually. These registers may be used by the system manufacturers to store security and other
important information separately from the main memory array.
The Erase Security Register instruction is similar to the Sector Erase instruction. A Write Enable
instruction must be executed before the device will accept the Erase Security Register Instruction
(Status Register bit WEL must equal 1). The instruction is initiated by driving the /CS pin low and shifting
the instruction code “44h” followed by a 24-bit address (A23-A0) to erase one of the four security
Security Register #1
Security Register #2
Security Register #3
Don’t Care
Don’t Care
Don’t Care
The Erase Security Register instruction sequence is shown in figure 35. The /CS pin must be driven
high after the eighth bit of the last byte has been latched. If this is not done the instruction will not be
executed. After /CS is driven high, the self-timed Erase Security Register operation will commence for
a time duration of tSE (See AC Characteristics). While the Erase Security Register cycle is in progress,
the Read Status Register instruction may still be accessed for checking the status of the BUSY bit. The
BUSY bit is a 1 during the erase cycle and becomes a 0 when the cycle is finished and the device is
ready to accept other instructions again. After the Erase Security Register cycle has finished the Write
Enable Latch (WEL) bit in the Status Register is cleared to 0. The Security Register Lock Bits (LB3-1)
in the Status Register-2 can be used to OTP protect the security registers. Once a lock bit is set to 1,
the corresponding security register will be permanently locked, Erase Security Register instruction to
that register will be ignored (See 8.1.9 for detail descriptions).
Instruction (44h)
Figure 35. Erase Security Registers Instruction Sequence
- 51 -
Publication Release Date:July 21, 2015
Prelimry-Revision G
Direct download click here

The W25Q80DV (8M-bit) Serial Flash memory provides a storage solution for systems with limited space, pins and power. The 25Q series offers flexibility and performance well beyond ordinary Serial Flash devices. They are ideal for code shadowing to RAM, executing code directly from Dual/Quad SPI (XIP) and storing voice, text and data. The device operates on a single 2.7V to 3.6V power supply with current consumption as low as 1µA for power-down. All devices are offered in space-saving packages.
The W25Q80DV array is organized into 4,096 programmable pages of 256-bytes each. Up to 256 bytes can be programmed at a time. Pages can be erased in groups of 16 (4KB sector erase), groups of 128 (32KB block erase), groups of 256 (64KB block erase) or the entire chip (chip erase). The W25Q80DV has 256 erasable sectors and 16 erasable blocks respectively. The small 4KB sectors allow for greater flexibility in applications that require data and parameter storage. (See figure 2.)
The W25Q80DV supports the standard Serial Peripheral Interface (SPI), and a high performance Dual/Quad output as well as Dual/Quad I/O SPI: Serial Clock, Chip Select, Serial Data I/O0 (DI), I/O1 (DO), I/O2 (/WP), and I/O3 (/HOLD). SPI clock frequencies of up to 104MHz are supported allowing equivalent clock rates of 208MHz (104MHz x 2) for Dual I/O and 416MHz (104MHz x 4) for Quad I/O when using the Fast Read Dual/Quad I/O instructions. These transfer rates can outperform standard Asynchronous 8 and 16-bit Parallel Flash memories. A Hold pin, Write Protect pin and programmable write protection, with top, bottom or complement array control, provide further control flexibility. Additionally, the device supports JEDEC standard manufacturer and device identification with a 64-bit Unique Serial Number.

● Family of SpiFlash Memories
   – W25Q80DV: 8M-bit/1M-byte (1,048,576)
   – 256-byte per programmable page
   – Standard SPI: CLK,/CS,DI,DO,/WP,/Hold
   – Dual SPI: CLK, /CS, IO0, IO1, /WP, /Hold
   – Quad SPI: CLK, /CS, IO0, IO1, IO2, IO3
   – Uniform 4KB Sectors, 32KB & 64KB Blocks
● Highest Performance Serial Flash
   – 104MHz Dual/Quad SPI clocks
   – 208/416MHz equivalent Dual/Quad SPI
   – 50MB/S continuous data transfer rate
● Software and Hardware Write Protection
   – Write-Protect all or portion of memory
   – Enable/Disable protection with /WP pin
   – Top or bottom array protection
● Flexible Architecture with 4KB sectors
   – Uniform Sector/Block Erase (4/32/64-kbytes)
   – Program one to 256 bytes < 0.8ms
   – Erase/Program Suspend & Resume
   – More than 100,000 erase/write cycles
   – More than 20-year data retention
● Low Power, Wide Temperature Range
   – Single 2.7 to 3.6V supply
   – <1µA Power-down(typ.)
● Space Efficient Packaging(1):
   – 8-pin SOIC 150-mil/208mil, VSOP 150-mil
   – 8-pad WSON 6x5-mm, USON 2x3-mm
   – 8-pin PDIP 300-mil
   – 8-ball WLCSP
   – Contact Winbond for KGD and other options

Share Link : Winbond
@ 2014 - 2018  [ Home ] [ Privacy Policy ] [ Request Datasheet ] [ Contact Us ]