datasheetbank_Logo    Integrated circuits, Transistor, Semiconductors Search and Datasheet PDF Download Site
Part Name :

W25Q80DVZPI View Datasheet(PDF) - Winbond

Part NameW25Q80DVZPI Winbond
Winbond Winbond
Description3V 8M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI
W25Q80DVZPI Datasheet PDF : 71 Pages
First Prev 41 42 43 44 45 46 47 48 49 50 Next Last
W25Q80DV
Read Manufacturer / Device ID Dual I/O (92h)
The Manufacturer / Device ID Dual I/O instruction is an alternative to the Read Manufacturer/Device ID
instruction that provides both the JEDEC assigned manufacturer ID and the specific device ID at 2x
speed.
The Read Manufacturer / Device ID Dual I/O instruction is similar to the Fast Read Dual I/O instruction.
The instruction is initiated by driving the /CS pin low and shifting the instruction code “92h” followed by
a 24-bit address (A23-A0) of 000000h, but with the capability to input the Address bits two bits per clock.
After which, the Manufacturer ID for Winbond (EFh) and the Device ID are shifted out 2 bits per clock
on the falling edge of CLK with most significant bits (MSB) first as shown in figure 30. The Device ID
values for the W25Q80DV are listed in Manufacturer and Device Identification table. The Manufacturer
and Device IDs can be read continuously, alternating from one to the other. The instruction is completed
by driving /CS high.
/CS
CLK
Mode 3
Mode 0
DI
(IO0)
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23
Instruction (92h)
A23-16
A15-8
A7-0 (00h)
M7-0
6420642064206420
DO
(IO1)
* = MSB
High Impedance
7531753175317531
*
*
*
*
/CS
CLK
DI
(IO0)
DO
(IO1)
23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38
IOs switch from
Input to Output
06420642064206420
17531753175317531
* MFR ID
* Device ID
* MFR ID
(repeat)
* Device ID
(repeat)
Mode 3
Mode 0
Figure 30. Read Manufacturer / Device ID Dual I/O Diagram
Note:
1. The “Continuous Read Mode” bits M7-0 must be set to FFh to be compatible with Fast Read Dual I/O instruction.
- 46 -
Publication Release Date:July 21, 2015
Prelimry-Revision G
Direct download click here
 

GENERAL DESCRIPTION
The W25Q80DV (8M-bit) Serial Flash memory provides a storage solution for systems with limited space, pins and power. The 25Q series offers flexibility and performance well beyond ordinary Serial Flash devices. They are ideal for code shadowing to RAM, executing code directly from Dual/Quad SPI (XIP) and storing voice, text and data. The device operates on a single 2.7V to 3.6V power supply with current consumption as low as 1µA for power-down. All devices are offered in space-saving packages.
The W25Q80DV array is organized into 4,096 programmable pages of 256-bytes each. Up to 256 bytes can be programmed at a time. Pages can be erased in groups of 16 (4KB sector erase), groups of 128 (32KB block erase), groups of 256 (64KB block erase) or the entire chip (chip erase). The W25Q80DV has 256 erasable sectors and 16 erasable blocks respectively. The small 4KB sectors allow for greater flexibility in applications that require data and parameter storage. (See figure 2.)
The W25Q80DV supports the standard Serial Peripheral Interface (SPI), and a high performance Dual/Quad output as well as Dual/Quad I/O SPI: Serial Clock, Chip Select, Serial Data I/O0 (DI), I/O1 (DO), I/O2 (/WP), and I/O3 (/HOLD). SPI clock frequencies of up to 104MHz are supported allowing equivalent clock rates of 208MHz (104MHz x 2) for Dual I/O and 416MHz (104MHz x 4) for Quad I/O when using the Fast Read Dual/Quad I/O instructions. These transfer rates can outperform standard Asynchronous 8 and 16-bit Parallel Flash memories. A Hold pin, Write Protect pin and programmable write protection, with top, bottom or complement array control, provide further control flexibility. Additionally, the device supports JEDEC standard manufacturer and device identification with a 64-bit Unique Serial Number.

FEATURES
● Family of SpiFlash Memories
   – W25Q80DV: 8M-bit/1M-byte (1,048,576)
   – 256-byte per programmable page
   – Standard SPI: CLK,/CS,DI,DO,/WP,/Hold
   – Dual SPI: CLK, /CS, IO0, IO1, /WP, /Hold
   – Quad SPI: CLK, /CS, IO0, IO1, IO2, IO3
   – Uniform 4KB Sectors, 32KB & 64KB Blocks
● Highest Performance Serial Flash
   – 104MHz Dual/Quad SPI clocks
   – 208/416MHz equivalent Dual/Quad SPI
   – 50MB/S continuous data transfer rate
● Software and Hardware Write Protection
   – Write-Protect all or portion of memory
   – Enable/Disable protection with /WP pin
   – Top or bottom array protection
● Flexible Architecture with 4KB sectors
   – Uniform Sector/Block Erase (4/32/64-kbytes)
   – Program one to 256 bytes < 0.8ms
   – Erase/Program Suspend & Resume
   – More than 100,000 erase/write cycles
   – More than 20-year data retention
● Low Power, Wide Temperature Range
   – Single 2.7 to 3.6V supply
   – <1µA Power-down(typ.)
● Space Efficient Packaging(1):
   – 8-pin SOIC 150-mil/208mil, VSOP 150-mil
   – 8-pad WSON 6x5-mm, USON 2x3-mm
   – 8-pin PDIP 300-mil
   – 8-ball WLCSP
   – Contact Winbond for KGD and other options

Share Link : Winbond
@ 2014 - 2018  [ Home ] [ Privacy Policy ] [ Request Datasheet ] [ Contact Us ]