datasheetbank_Logo    Integrated circuits, Transistor, Semiconductors Search and Datasheet PDF Download Site
Part Name :


W25Q80DVZPI View Datasheet(PDF) - Winbond

Part NameW25Q80DVZPI Winbond
Winbond Winbond
Description3V 8M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI


W25Q80DVZPI Datasheet PDF : 71 Pages
First Prev 21 22 23 24 25 26 27 28 29 30 Next Last
W25Q80DV
8.5 Instruction Descriptions
Write Enable (06h)
The Write Enable instruction (Figure 4) sets the Write Enable Latch (WEL) bit in the Status Register to
a 1. The WEL bit must be set prior to every Page Program, Quad Page Program, Sector Erase, Block
Erase, Chip Erase, Write Status Register and Erase/Program Security Registers instruction. The Write
Enable instruction is entered by driving /CS low, shifting the instruction code “06h” into the Data Input
(DI) pin on the rising edge of CLK, and then driving /CS high.
Figure 4. Write Enable Instruction
Write Enable for Volatile Status Register (50h)
The non-volatile Status Register bits described in section 7.1 can also be written to as volatile bits. This
gives more flexibility to change the system configuration and memory protection schemes quickly
without waiting for the typical non-volatile bit write cycles or affecting the endurance of the Status
Register non-volatile bits. To write the volatile values into the Status Register bits, the Write Enable for
Volatile Status Register (50h) instruction must be issued prior to a Write Status Register (01h)
instruction. Write Enable for Volatile Status Register instruction (Figure 5) will not set the Write Enable
Latch (WEL) bit, it is only valid for the Write Status Register instruction to change the volatile Status
Register bit values.
/CS
CLK
DI
(IO0)
DO
(IO1)
Mode 3
Mode 0
01234567
Mode 3
Mode 0
Instruction (50h)
/CS
CLK
IO0
Mode 3
Mode 0
01
Instruction
50h
IO1
High Impedance
IO2
IO3
Figure 5. Write Enable for Volatile Status Register Instruction Sequence Diagram
Mode 3
Mode 0
- 22 -
Publication Release Date:July 21, 2015
Prelimry-Revision G
Direct download click here

GENERAL DESCRIPTION
The W25Q80DV (8M-bit) Serial Flash memory provides a storage solution for systems with limited space, pins and power. The 25Q series offers flexibility and performance well beyond ordinary Serial Flash devices. They are ideal for code shadowing to RAM, executing code directly from Dual/Quad SPI (XIP) and storing voice, text and data. The device operates on a single 2.7V to 3.6V power supply with current consumption as low as 1µA for power-down. All devices are offered in space-saving packages.
The W25Q80DV array is organized into 4,096 programmable pages of 256-bytes each. Up to 256 bytes can be programmed at a time. Pages can be erased in groups of 16 (4KB sector erase), groups of 128 (32KB block erase), groups of 256 (64KB block erase) or the entire chip (chip erase). The W25Q80DV has 256 erasable sectors and 16 erasable blocks respectively. The small 4KB sectors allow for greater flexibility in applications that require data and parameter storage. (See figure 2.)
The W25Q80DV supports the standard Serial Peripheral Interface (SPI), and a high performance Dual/Quad output as well as Dual/Quad I/O SPI: Serial Clock, Chip Select, Serial Data I/O0 (DI), I/O1 (DO), I/O2 (/WP), and I/O3 (/HOLD). SPI clock frequencies of up to 104MHz are supported allowing equivalent clock rates of 208MHz (104MHz x 2) for Dual I/O and 416MHz (104MHz x 4) for Quad I/O when using the Fast Read Dual/Quad I/O instructions. These transfer rates can outperform standard Asynchronous 8 and 16-bit Parallel Flash memories. A Hold pin, Write Protect pin and programmable write protection, with top, bottom or complement array control, provide further control flexibility. Additionally, the device supports JEDEC standard manufacturer and device identification with a 64-bit Unique Serial Number.

FEATURES
● Family of SpiFlash Memories
   – W25Q80DV: 8M-bit/1M-byte (1,048,576)
   – 256-byte per programmable page
   – Standard SPI: CLK,/CS,DI,DO,/WP,/Hold
   – Dual SPI: CLK, /CS, IO0, IO1, /WP, /Hold
   – Quad SPI: CLK, /CS, IO0, IO1, IO2, IO3
   – Uniform 4KB Sectors, 32KB & 64KB Blocks
● Highest Performance Serial Flash
   – 104MHz Dual/Quad SPI clocks
   – 208/416MHz equivalent Dual/Quad SPI
   – 50MB/S continuous data transfer rate
● Software and Hardware Write Protection
   – Write-Protect all or portion of memory
   – Enable/Disable protection with /WP pin
   – Top or bottom array protection
● Flexible Architecture with 4KB sectors
   – Uniform Sector/Block Erase (4/32/64-kbytes)
   – Program one to 256 bytes < 0.8ms
   – Erase/Program Suspend & Resume
   – More than 100,000 erase/write cycles
   – More than 20-year data retention
● Low Power, Wide Temperature Range
   – Single 2.7 to 3.6V supply
   – <1µA Power-down(typ.)
● Space Efficient Packaging(1):
   – 8-pin SOIC 150-mil/208mil, VSOP 150-mil
   – 8-pad WSON 6x5-mm, USON 2x3-mm
   – 8-pin PDIP 300-mil
   – 8-ball WLCSP
   – Contact Winbond for KGD and other options

Share Link : Winbond

@ 2014 - 2018  [ Home ] [ Privacy Policy ] [ Request Datasheet ] [ Contact Us ]