datasheetbank_Logo    Integrated circuits, Transistor, Semiconductors Search and Datasheet PDF Download Site
Part Name :

W25Q80DVZPI View Datasheet(PDF) - Winbond

Part NameW25Q80DVZPI Winbond
Winbond Winbond
W25Q80DVZPI Datasheet PDF : 71 Pages
First Prev 11 12 13 14 15 16 17 18 19 20 Next Last
The Read Status Register-1 and Status Register-2 instructions can be used to provide status on the
availability of the Flash memory array, if the device is write enabled or disabled, the state of write
protection, Quad SPI setting, Security Register lock status and Erase/Program Suspend status. The
Write Status Register instruction can be used to configure the device write protection features, Quad SPI
setting and Security Register OTP lock. Write access to the Status Register is controlled by the state of
the non-volatile Status Register Protect bits (SRP0, SRP1), the Write Enable instruction, and during
Standard/Dual SPI operations, the /WP pin.
BUSY is a read only bit in the status register (S0) that is set to a 1 state when the device is executing a
Page Program, Quad Page Program, Sector Erase, Block Erase, Chip Erase, Write Status Register or
Erase/Program Security Register instruction. During this time the device will ignore further instructions
except for the Read Status Register and Erase/Program Suspend instruction (see tW, tPP, tSE, tBE, and
tCE in AC Characteristics). When the program, erase or write status/security register instruction has
completed, the BUSY bit will be cleared to a 0 state indicating the device is ready for further instructions.
Write Enable Latch (WEL)
Write Enable Latch (WEL) is a read only bit in the status register (S1) that is set to 1 after executing a
Write Enable Instruction. The WEL status bit is cleared to 0 when the device is write disabled. A write
disable state occurs upon power-up or after any of the following instructions finished: Write Disable,
Page Program, Quad Page Program, Sector Erase, Block Erase, Chip Erase, Write Status Register,
Erase Security Register and Program Security Register.
Block Protect Bits (BP2, BP1, BP0)
The Block Protect Bits (BP2, BP1, BP0) are non-volatile read/write bits in the status register (S4, S3,
and S2) that provide Write Protection control and status. Block Protect bits can be set using the Write
Status Register Instruction (see tW in AC characteristics). All, none or a portion of the memory array can
be protected from Program and Erase instructions (see Status Register Memory Protection table). The
factory default setting for the Block Protection Bits is 0, none of the array protected.
Top/Bottom Block Protect (TB)
The non-volatile Top/Bottom bit (TB) controls if the Block Protect Bits (BP2, BP1, BP0) protect from the
Top (TB=0) or the Bottom (TB=1) of the array as shown in the Status Register Memory Protection table.
The factory default setting is TB=0. The TB bit can be set with the Write Status Register Instruction
depending on the state of the SRP0, SRP1 and WEL bits.
Sector/Block Protect (SEC)
The non-volatile Sector/Block Protect bit (SEC) controls if the Block Protect Bits (BP2, BP1, BP0) protect
either 4KB Sectors (SEC=1) or 64KB Blocks (SEC=0) in the Top (TB=0) or the Bottom (TB=1) of the
array as shown in the Status Register Memory Protection table. The default setting is SEC=0.
Complement Protect (CMP)
The Complement Protect bit (CMP) is a non-volatile read/write bit in the status register (S14). It is used
in conjunction with SEC, TB, BP2, BP1 and BP0 bits to provide more flexibility for the array protection.
Once CMP is set to 1, previous array protection set by SEC, TB, BP2, BP1 and BP0 will be reversed.
- 13 -
Publication Release Date:July 21, 2015
Prelimry-Revision G
Direct download click here

The W25Q80DV (8M-bit) Serial Flash memory provides a storage solution for systems with limited space, pins and power. The 25Q series offers flexibility and performance well beyond ordinary Serial Flash devices. They are ideal for code shadowing to RAM, executing code directly from Dual/Quad SPI (XIP) and storing voice, text and data. The device operates on a single 2.7V to 3.6V power supply with current consumption as low as 1µA for power-down. All devices are offered in space-saving packages.
The W25Q80DV array is organized into 4,096 programmable pages of 256-bytes each. Up to 256 bytes can be programmed at a time. Pages can be erased in groups of 16 (4KB sector erase), groups of 128 (32KB block erase), groups of 256 (64KB block erase) or the entire chip (chip erase). The W25Q80DV has 256 erasable sectors and 16 erasable blocks respectively. The small 4KB sectors allow for greater flexibility in applications that require data and parameter storage. (See figure 2.)
The W25Q80DV supports the standard Serial Peripheral Interface (SPI), and a high performance Dual/Quad output as well as Dual/Quad I/O SPI: Serial Clock, Chip Select, Serial Data I/O0 (DI), I/O1 (DO), I/O2 (/WP), and I/O3 (/HOLD). SPI clock frequencies of up to 104MHz are supported allowing equivalent clock rates of 208MHz (104MHz x 2) for Dual I/O and 416MHz (104MHz x 4) for Quad I/O when using the Fast Read Dual/Quad I/O instructions. These transfer rates can outperform standard Asynchronous 8 and 16-bit Parallel Flash memories. A Hold pin, Write Protect pin and programmable write protection, with top, bottom or complement array control, provide further control flexibility. Additionally, the device supports JEDEC standard manufacturer and device identification with a 64-bit Unique Serial Number.

● Family of SpiFlash Memories
   – W25Q80DV: 8M-bit/1M-byte (1,048,576)
   – 256-byte per programmable page
   – Standard SPI: CLK,/CS,DI,DO,/WP,/Hold
   – Dual SPI: CLK, /CS, IO0, IO1, /WP, /Hold
   – Quad SPI: CLK, /CS, IO0, IO1, IO2, IO3
   – Uniform 4KB Sectors, 32KB & 64KB Blocks
● Highest Performance Serial Flash
   – 104MHz Dual/Quad SPI clocks
   – 208/416MHz equivalent Dual/Quad SPI
   – 50MB/S continuous data transfer rate
● Software and Hardware Write Protection
   – Write-Protect all or portion of memory
   – Enable/Disable protection with /WP pin
   – Top or bottom array protection
● Flexible Architecture with 4KB sectors
   – Uniform Sector/Block Erase (4/32/64-kbytes)
   – Program one to 256 bytes < 0.8ms
   – Erase/Program Suspend & Resume
   – More than 100,000 erase/write cycles
   – More than 20-year data retention
● Low Power, Wide Temperature Range
   – Single 2.7 to 3.6V supply
   – <1µA Power-down(typ.)
● Space Efficient Packaging(1):
   – 8-pin SOIC 150-mil/208mil, VSOP 150-mil
   – 8-pad WSON 6x5-mm, USON 2x3-mm
   – 8-pin PDIP 300-mil
   – 8-ball WLCSP
   – Contact Winbond for KGD and other options

Share Link : Winbond
@ 2014 - 2018  [ Home ] [ Privacy Policy ] [ Request Datasheet ] [ Contact Us ]