MC33065P-L View Datasheet(PDF) - Motorola => Freescale

Part Name

Description

View to exact match

MC33065P-L

High performance dual channel current mode controller

Motorola => Freescale 

MC34065–H, L MC33065–H, L

OPERATING DESCRIPTION

The MC34065–H,L series are high performance, fixed

frequency, dual channel current mode controllers specifically

designed for Off–Line and dc–to–dc converter applications.

These devices offer the designer a cost effective solution with

minimal external components where independent regulation

of two power converters is required. The Representative

Block Diagram is shown in Figure 15. Each channel contains

a high gain error amplifier, current sensing comparator, pulse

width modulator latch, and totem pole output driver. The

oscillator, reference regulator, and undervoltage lock–out

circuits are common to both channels.

Oscillator

The unique oscillator configuration employed features

precise frequency and duty cycle control. The frequency is

programmed by the values selected for the timing

components RT and CT. Capacitor CT is charged and

discharged by an equal magnitude internal current source

and sink, generating a symmetrical 50 percent duty cycle

waveform at Pin 2. The oscillator peak and valley thresholds

are 3.5 V and 1.6 V respectively. The source/sink current

magnitude is controlled by resistor RT. For proper operation

over temperature it must be in the range of 4.0 kΩ to 16 kΩ as

shown in Figure 1.

As CT charges and discharges, an internal blanking pulse

is generated that alternately drives the center inputs of the

upper and lower NOR gates high. This, in conjunction with a

precise amount of delay time introduced into each channel,

produces well defined non–overlapping output duty cycles.

Output 2 is enabled while CT is charging, and Output 1 is

enabled during the discharge. Figure 2 shows the Maximum

Output Duty Cycle versus Oscillator Frequency. Note that

even at 500 kHz, each output is capable of approximately

44% on–time, making this controller suitable for high

frequency power conversion applications.

In many noise sensitive applications it may be desirable to

frequency–lock the converter to an external system clock.

This can be accomplished by applying a clock signal as

shown in Figure 17. For reliable locking, the free–running

oscillator frequency should be set about 10% less than the

clock frequency. Referring to the timing diagram shown in

Figure 16, the rising edge of the clock signal applied to the

Sync input, terminates charging of CT and Drive Output 2

conduction. By tailoring the clock waveform symmetry,

accurate duty cycle clamping of either output can be

achieved. A circuit method for this, and multi–unit

synchronization, is shown in Figure 18.

Error Amplifier

Each channel contains a fully–compensated Error

Amplifier with access to the inverting input and output. The

amplifier features a typical dc voltage gain of 100 dB, and a

unity gain bandwidth of 1.0 MHz with 71° of phase margin

(Figure 5). The noninverting input is internally biased at 2.5 V

and is not pinned out. The converter output voltage is

typically divided down and monitored by the inverting input

through a resistor divider. The maximum input bias current is

–1.0 µA which will cause an output voltage error that is equal

to the product of the input bias current and the equivalent

input divider source resistance.

The Error Amp output (Pin 5, 12) is provided for external

loop compensation. The output voltage is offset by two diode

drops (≈1.4 V) and divided by three before it connects to the

inverting input of the Current Sense Comparator. This

guarantees that no pulses appear at the Drive Output (Pin 7,

10) when the error amplifier output is at its lowest state (VOL).

This occurs when the power supply is operating and the load

is removed, or at the beginning of a soft–start interval

(Figures 20, 21).

The minimum allowable Error Amp feedback resistance is

limited by the amplifier’s source current (0.5 mA) and the

output voltage (VOH) required to reach the comparator’s 1.0 V

clamp level with the inverting input at ground. This condition

happens during initial system startup or when the sensed

output is shorted:

) Rf(min) ≈

3.0

(1.0 V)

0.5 mA

1.4

V

= 8800 Ω

Current Sense Comparator and PWM Latch

The MC34065 operates as a current mode controller,

whereby output switch conduction is initiated by the oscillator

and terminated when the peak inductor current reaches the

threshold level established by the Error Amplifier output.

Thus the error signal controls the peak inductor current on a

cycle–by–cycle basis. The Current Sense Comparator–PWM

Latch configuration used ensures that only a single pulse

appears at the Drive Output during any given oscillator cycle.

The inductor current is converted to a voltage by inserting a

ground–referenced sense resistor RS in series with the

source of output switch Q1. This voltage is monitored by the

Current Sense Input (Pin 6, 11) and compared to a level

derived from the Error Amp output. The peak inductor current

under normal operating conditions is controlled by the

voltage at Pin 5, 12 where:

Ipk =

V(Pin 5, 12) – 1.4 V

3 RS

Abnormal operating conditions occur when the power

supply output is overloaded or if output voltage sensing is

lost. Under these conditions, the Current Sense Comparator

threshold will be internally clamped to 1.0 V. Therefore the

maximum peak switch current is:

Ipk(max) =

1.0 V

RS

When designing a high power switching regulator it may

be desirable to reduce the internal clamp voltage in order to

keep the power dissipation of RS to a reasonable level. A

simple method to adjust this voltage is shown in Figure 19.

The two external diodes are used to compensate the internal

diodes, yielding a constant clamp voltage over temperature.

Erratic operation due to noise pickup can result if there is an

excessive reduction of the Ipk(max) clamp voltage.

A narrow spike on the leading edge of the current

waveform can usually be observed and may cause the power

supply to exhibit an instability when the output is lightly

loaded. This spike is due to the power transformer

interwinding capacitance and output rectifier recovery time.

The addition of an RC filter on the Current Sense input with a

time constant that approximates the spike duration will

usually eliminate the instability, refer to Figure 24.

6

MOTOROLA ANALOG IC DEVICE DATA

Share Link: