datasheetbank_Logo
Integrated circuits, Transistor, Semiconductors Search and Datasheet PDF Download Site

HA-5020 View Datasheet(PDF) - Intersil

Part Name
Description
View to exact match
HA-5020 Datasheet PDF : 23 Pages
1 2 3 4 5 6 7 8 9 10 Next Last
HA-5020
Electrical Specifications
V+ = +5V, V- = -5V, RF = 1kΩ, AV = +1, RL = 400Ω, CL 10pF, Unless Otherwise Specified.
Parameters are not tested. The limits are guaranteed based on lab characterizations, and reflect
lot-to-lot variation. (Continued)
PARAMETER
TEMP.
TEST CONDITIONS
(°C)
MIN
TYP
MAX
UNITS
-3dB Bandwidth (Note 14)
Settling Time to 1%
VOUT = 100mV
2V Output Step
25
-
65
-
MHz
25
-
75
-
ns
Settling Time to 0.25%
2V Output Step
25
-
130
-
ns
INTERSIL VALUE ADDED SPECIFICATIONS
Input Noise Voltage (Note 14)
f = 1kHz
25
-
4.5
-
nV/Hz
+Input Noise Current (Note 14)
-Input Noise Current (Note 14)
Input Common Mode Range
Output Current, Short Circuit
Output Current, Disabled (Note 14)
Output Disable Time (Notes 14, 20)
f = 1kHz
25
-
2.5
f = 1kHz
25
-
25
Full
±2.5V
VIN = ±2.5V, VOUT = 0V
Full
±40
±60
DISABLE = 0V,
Full
-
-
VOUT = ±2.5V, VIN = 0V
25
-
40
-
pA/Hz
-
pA/Hz
-
V
-
mA
2
µA
-
µs
Output Enable Time (Notes 14, 21)
25
-
40
-
ns
Supply Voltage Range
25
±5
-
±15
V
Output Capacitance, Disabled (Note 19)
DISABLE = 0V
25
-
6
-
pF
VIDEO CHARACTERISTICS
Differential Gain (Notes 13, 14)
Differential Phase (Notes 13, 14)
Gain Flatness
RL = 150
RL = 150
To 5MHz
25
-
0.03
-
%
25
-
0.03
-
°
25
-
0.1
-
dB
NOTES:
2. Suggested VOS Adjust Circuit: The inverting input current (-IBIAS) can be adjusted with an external 10kpot between pins 1 and 5, wiper
connected to V+. Since -IBIAS flows through the feedback resistor (RF), the result is an adjustment in offset voltage. The amount of offset voltage
adjustment is determined by the value of RF (VOS = -IBIAS*RF).
3. RL = 100, VIN = 10V. This is the minimum current which must be pulled out of the Disable pin in order to disable the output. The output is
considered disabled when -10mV VOUT +10mV.
4. VIN = 0V. This is the maximum current that can be pulled out of the Disable pin with the HA-5020 remaining enabled. The HA-5020 is considered
disabled when the supply current has decreased by at least 0.5mA.
5. VOUT switches from -10V to +10V, or from +10V to -10V. Specification is from the 25% to 75% points.
6.
FPBW
=
S----l--e---w------R----a----t-e--
2πVPEAK
;
VPEAK
= 10V.
7. RL = 100, VOUT = 1V. Measured from 10% to 90% points for rise/fall times; from 50% points of input and output for propagation delay.
8. This parameter is not tested. The limits are guaranteed based on lab characterization, and reflect lot-to-lot variation.
9. VIN = +10V, Disable = +15V to 0V. Measured from the 50% point of Disable to VOUT = 0V.
10. VIN = +10V, Disable = 0V to +15V. Measured from the 50% point of Disable to VOUT = 10V.
11. VIN = 0V, Force VOUT from 0V to ±10V, tR = tF = 50ns.
12. Measured with a VM700A video tester using a NTC-7 composite VITS.
13. See “Typical Performance Curves” for more information.
14. VCM = ±2.5V. At -40°C product is tested at VCM = ±2.25V because short test duration does not allow self heating.
15. RL = 100. VIN = 2.5V. This is the minimum current which must be pulled out of the Disable pin in order to disable the output. The output is
considered disabled when -10mV VOUT +10mV.
16. VOUT switches from -2V to +2V, or from +2V to -2V. Specification is from the 25% to 75% points.
17. FPBW = S-2---πl--e--V-w---P---R-E---a-A---t-Ke-- ; VPEAK = 2V .
18. VIN = 0V, Force VOUT from 0V to ±2.5V, tR = tF = 50ns.
19. VIN = +2V, Disable = +5V to 0V. Measured from the 50% point of Disable to VOUT = 0V.
20. VIN = +2V, Disable = 0V to +5V. Measured from the 50% point of Disable to VOUT = 2V.
7
FN2845.11
June 5, 2006
 

Share Link: 

datasheetbank.com [ Privacy Policy ] [ Request Datasheet ] [ Contact Us ]