datasheetbank_Logo   Технический паспорт Поисковая и бесплатно техническое описание Скачать
Номер в каталоге  

Z0103MARLRFG Просмотр технического описания (PDF) - ON Semiconductor

Номер в каталогеКомпоненты Описаниепроизводитель
Z0103MARLRFG Sensitive Gate Triacs Series Silicon Bidirectional Thyristors ON-Semiconductor
ON Semiconductor ON-Semiconductor
Z0103MARLRFG Datasheet PDF : 10 Pages
1 2 3 4 5 6 7 8 9 10
Z0103MA, Z0107MA, Z0109MA
TO92 EIA RADIAL TAPE IN FAN FOLD BOX OR ON REEL
H2A
H2A
H2B
H2B
H
H4 H5
W2
T1
L1 H1
W1 W
L
T
F1
T2
F2
P2
P2
D
P1
P
Figure 12. Device Positioning on Tape
Specification
Inches
Millimeter
Symbol
Item
Min
Max
Min
Max
D
Tape Feedhole Diameter
0.1496 0.1653
3.8
4.2
D2
Component Lead Thickness Dimension
0.015
0.020
0.38
0.51
F1, F2 Component Lead Pitch
0.0945 0.110
2.4
2.8
H
Bottom of Component to Seating Plane
0.059
0.156
1.5
4.0
H1
Feedhole Location
0.3346 0.3741
8.5
9.5
H2A
Deflection Left or Right
0
0.039
0
1.0
H2B
Deflection Front or Rear
0
0.051
0
1.0
H4
Feedhole to Bottom of Component
0.7086 0.768
18
19.5
H5
Feedhole to Seating Plane
0.610
0.649
15.5
16.5
L
Defective Unit Clipped Dimension
0.3346 0.433
8.5
11
L1
Lead Wire Enclosure
0.09842
2.5
P
Feedhole Pitch
0.4921 0.5079
12.5
12.9
P1
Feedhole Center to Center Lead
0.2342 0.2658
5.95
6.75
P2
First Lead Spacing Dimension
0.1397 0.1556
3.55
3.95
T
Adhesive Tape Thickness
0.06
0.08
0.15
0.20
T1
Overall Taped Package Thickness
0.0567
1.44
T2
Carrier Strip Thickness
0.014
0.027
0.35
0.65
W
Carrier Strip Width
0.6889 0.7481
17.5
19
W1
Adhesive Tape Width
0.2165 0.2841
5.5
6.3
W2
Adhesive Tape Position
.0059 0.01968 0.15
0.5
2. Maximum alignment deviation between leads not to be greater than 0.2 mm.
3. Defective components shall be clipped from the carrier tape such that the remaining protrusion (L) does not exceed a maximum of 11 mm.
4. Component lead to tape adhesion must meet the pull test requirements.
5. Maximum noncumulative variation between tape feed holes shall not exceed 1 mm in 20 pitches.
6. Holddown tape not to extend beyond the edge(s) of carrier tape and there shall be no exposure of adhesive.
7. No more than 1 consecutive missing component is permitted.
8. A tape trailer and leader, having at least three feed holes is required before the first and after the last component.
9. Splices will not interfere with the sprocket feed holes.
http://onsemi.com
8
Direct download click here
 

Share Link : ON-Semiconductor
All Rights Reserved © datasheetbank.com 2014 - 2019 [ политика конфиденциальности ] [ Запрос Даташит ]