datasheetbank_Logo
Integrated circuits, Transistor, Semiconductors Search and Datasheet PDF Download Site

LM311DR2 View Datasheet(PDF) - ON Semiconductor

Part Name
Description
View to exact match
LM311DR2
ON-Semiconductor
ON Semiconductor ON-Semiconductor
LM311DR2 Datasheet PDF : 10 Pages
1 2 3 4 5 6 7 8 9 10
LM211, LM311
ELECTRICAL CHARACTERISTICS (VCC = +15 V, VEE = −15 V, TA = 25°C, unless otherwise noted) Note 1
LM211
LM311
Characteristic
Symbol
Min Typ Max Min Typ Max
Unit
Input Offset Voltage (Note 3)
RS 50 kW, TA = +25°C
RS 50 kW, Tlow TA Thigh*
Input Offset Current (Note 3) TA = +25°C
Tlow TA Thigh*
Input Bias Current TA = +25°C
Tlow TA Thigh*
Voltage Gain
Response Time (Note 4)
VIO
mV
0.7 3.0
2.0 7.5
4.0
10
IIO
1.7 10
1.7 50
nA
20
70
IIB
45 100
45 250
nA
150
300
AV
40 200
40 200
V/mV
200
200
ns
Saturation Voltage
VID −5.0 mV, IO = 50 mA, TA = 25°C
VID −10 mV, IO = 50 mA, TA = 25°C
VCC 4.5 V, VEE = 0, Tlow TA Thigh*
VID 66.0 mV, Isink 8.0 mA
VID 610 mV, Isink 8.0 mA
Strobe ”On” Current (Note 5)
Output Leakage Current
VID 5.0 mV, VO= 35 V, TA = 25°C, Istrobe= 3.0 mA
VID 10 mV, VO= 35 V, TA = 25°C, Istrobe= 3.0 mA
VID 5.0 mV, VO= 35 V, Tlow TA Thigh*
Input Voltage Range (Tlow TA Thigh*)
VOL
IS
VICR
V
− 0.75 1.5
− 0.75 1.5
− 0.23 0.4
− 0.23 0.4
3.0
3.0
mA
0.2 10
nA
0.2 50
nA
0.1 0.5
mA
−14.5 −14.7 +13.0 −14.5 −14.7 +13.0
V
to
to
13.8
13.8
Positive Supply Current
ICC
− +2.4 +6.0 − +2.4 +7.5
mA
Negative Supply Current
IEE
− −1.3 −5.0 − −1.3 −5.0
mA
* LM211: Tlow = −25°C, Thigh = +85°C
LM311: Tlow = 0°C, Thigh = +70°C
1. Offset voltage, offset current and bias current specifications apply for a supply voltage range from a single 5.0 V supply up to ±15 V supplies.
2. This rating applies for ±15 V supplies. The positive input voltage limit is 30 V above the negative supply. The negative input voltage limit is
equal to the negative supply voltage or 30 V below the positive supply, whichever is less.
3. The offset voltages and offset currents given are the maximum values required to drive the output within a volt of either supply with a 1.0 mA
load. Thus, these parameters define an error band and take into account the “worst case” effects of voltage gain and input impedance.
4. The response time specified is for a 100 mV input step with 5.0 mV overdrive.
5. Do not short the strobe pin to ground; it should be current driven at 3.0 mA to 5.0 mA.
1.3 k
5 300
Balance
Balance/Strobe
6 300
2
Inputs
3
1.3 k
800 800
100
3.7 k 3.7 k
730 340
3.0 k
300
250
900
800
1.3 k
1.3 k 5.4 k
Figure 2. Circuit Schematic
http://onsemi.com
3
8
VCC
5.0 k
7
200 Output
600
1
GND
4
VEE
 

Share Link: 

datasheetbank.com [ Privacy Policy ] [ Request Datasheet ] [ Contact Us ]