74ALVC162334ADGG5 View Datasheet(PDF) - NXP Semiconductors.
Part Name
Description
View to exact match
74ALVC162334ADGG5
NXP Semiconductors.
74ALVC162334ADGG5 Datasheet PDF : 19 Pages
| |||
Nexperia
74ALVC162334A
16-bit registered driver (3-state)
10. Static characteristics
Table 7. Static characteristics
Tamb = −40 °C to +85 °C; over recommended operating conditions; voltages are referenced to GND (ground = 0 V);
unless otherwise specified.
Symbol Parameter
Conditions
Min
Typ[1]
Max Unit
VIH
VIL
VOH
VOL
ILI
IOZ
ICC
∆ICC
Ci
Cio
CPD
HIGH-level input voltage VCC = 2.3 V to 2.7 V
VCC = 2.7 V to 3.6 V
LOW-level input voltage VCC = 2.3 V to 2.7 V
VCC = 2.7 V to 3.6 V
HIGH-level output voltage VI = VIH or VIL
VCC = 2.3 V to 3.6 V; IO = −100 µA
VCC = 2.3 V; IO = −4 mA
VCC = 2.3 V; IO = −6 mA
VCC = 2.7 V; IO = −4 mA
VCC = 2.7 V; IO = −8 mA
VCC = 3.0 V; IO = −6 mA
VCC = 3.0 V; IO = −12 mA
LOW-level output voltage VI = VIH or VIL
VCC = 2.3 V to 3.6 V; IO = 100 µA
VCC = 2.3 V; IO = 4 mA
VCC = 2.3 V; IO = 6 mA
VCC = 2.7 V; IO = 4 mA
VCC = 2.7 V; IO = 8 mA
VCC = 3.0 V; IO = 6 mA
VCC = 3.0 V; IO = 12 mA
input leakage current
VCC = 2.3 V to 3.6 V;
VI = VCC or GND
off-state output current
3-state; VCC = 2.3 V to 3.6 V;
VI = VIH or VIL; VO = VCC or GND
supply current
VCC = 2.3 V to 3.6 V;
VI = VCC or GND; IO = 0 mA
additional supply current VCC = 2.3 V to 3.6 V;
VI = VCC − 0.6 V; IO = 0 mA
input capacitance
1.7
1.2
2.0
1.5
-
1.2
-
1.5
-
V
-
V
0.7 V
0.8 V
VCC − 0.2 VCC
-
V
VCC − 0.4 VCC − 0.11 -
V
VCC − 0.6 VCC − 0.17 -
V
VCC − 0.5 VCC − 0.09 -
V
VCC − 0.7 VCC − 0.19 -
V
VCC − 0.6 VCC − 0.13 -
V
VCC − 1.0 VCC − 0.27 -
V
-
GND
0.20 V
-
0.07
0.40 V
-
0.11
0.55 V
-
0.06
0.40 V
-
0.13
0.60 V
-
0.09
0.55 V
-
0.19
0.80 V
-
0.1
5
µA
-
0.1
10
µA
-
0.2
40
µA
-
150
750 µA
-
4.0
-
pF
input/output capacitance
-
8.0
-
pF
power dissipation
per buffer; VI = GND to VCC
[2]
capacitance
transparent mode; output enabled
-
10
-
pF
transparent mode; output disabled
-
3
-
pF
clocked mode; output enabled
-
21
-
pF
clocked mode; output disabled
-
15
-
pF
[1] All typical values are at Tamb = 25 °C.
[2] CPD is used to determine the dynamic power dissipation (PD) in µW.
PD = CPD × VCC2 × fi + Σ (CL × VCC2 × fo), where:
fi = input frequency in MHz;
74ALVC162334A_3
Product data sheet
Rev. 03 — 13 December 2006
© Nexperia B.V. 2017. All rights reserved
8 of 19
|
|
Share Link: