1EDI30J12CPXUMA1 View Datasheet(PDF) - Unspecified
Part Name
Description
View to exact match
1EDI30J12CPXUMA1 Datasheet PDF : 28 Pages
| |||
EiceDRIVER™ Enhanced
1EDI30J12CP
Characteristics
4.4
Electrical Characteristics
The electrical characteristics involve the spread of values given within the specified supply voltage and junction
temperature range TJ from -40°C to 150°C. Typical values represent the nominal values related to TJ=25°C.
Unless otherwise noticed, voltages of the input side signals (pins VCC1, IN, EN, GND1) are measured with respect
to input ground (pin GND1) all other voltages are measured with respect to positive output supply (pin VCC2).
Supply voltages are VVCC1 = 5 V and VVEE2 = -25 V if not otherwise mentioned.
The following characteristics are specified
• Power Supply (Table 5)
• Logic Input (Table 6)
• JFET Driver (Table 7)
• MOSFET Driver (Table 8)
• Dynamic Characteristics (Table 9)
Table 5 Power Supply
Parameter
VCC1 quiescent current
VCC1 quiescent current
VCC1 supply current
VCC1 turn on threshold
VCC1 turn off threshold
VCC1 turn on/off hysteresis
VEE2 quiescent current 1
VEE2 quiescent current 2
VREG output voltage1)2)
Symbol
IVCC1qu1
IVCC1qu2
IVCC1supp
VVCC1on
VVCC1off
VVCC1hys
IVEE2qu1
IVEE2qu2
VVREG0
Min.
—
120
—
4.15
3.9
0.15
—
—
-19.5
VREG output voltage loaded1)2) VVREG50
-19.0
VREG turn on threshold1)3)
VVREGon
VREG turn off threshold1)3)
VVREGoff
VREG turn on/off hysteresis1)3) VVREGhys
VREG turn on threshold BS1)3) VVREGonBS
VREG turn off threshold BS1)3) VVREGoffBS
VREG turn on/off hysteresis
BS1)3)
VVREGhysBS
VREG load current
IVREG
-17.4
-17.0
-9.8
-9.2
1) Voltage refer to VCC2
2) DC voltage
3) ULVO threshold output chip
Values
Typ.
430
Max.
650
240
500
1.2
1.6
4.55
4.75
4.25
4.55
380
500
800
1100
-18.85 -18.1
-18.25 -17.5
-16.9
-16.4
0.5
-9.5
-8.8
0.7
-16.4
-16.0
-9.0
-8.3
50
Unit Note / Test Condition
µA IN = statically low,
EN = statically high
µA EN = statically low
mA IN = 1MHz
V
V
V
µA output chip off due to
UVLO
µA IN = low,
output chip on
V
1µF from VREG to
VCC2, VVEE2< -22V,
Load 0mA
V
1µF from VREG to
VCC2, VVEE2< -22V,
Load 50mA
V
V
V
V
VBSEN > -3V1)
V
VBSEN > -3V1)
V
VBSEN > -3V1)
mA including loads from
MDrv and JFDrv
Preliminary Datasheet
16
Rev. 1.3, 2014-11-12
|
|
Share Link: 