datasheetbank_Logo
Integrated circuits, Transistor, Semiconductors Search and Datasheet PDF Download Site

TLP155 View Datasheet(PDF) - Toshiba

Part Name
Description
View to exact match
TLP155 Datasheet PDF : 10 Pages
1 2 3 4 5 6 7 8 9 10
TLP155
7. Absolute Maximum Ratings (Note) (Unless otherwise specified, Ta = 25)
Characteristics
Symbol Note
Rating
Unit
LED Input forward current
IF
20
mA
Input forward current derating
(Ta 92)
IF/Ta
-0.63
mA/
Peak transient input forward
current
IFPT
(Note 1)
1
A
Input reverse voltage
VR
5
V
Junction temperature
Tj
125
Detector Peak high-level output current
(Ta = -40 to 100)
IOPH
(Note 2)
-0.6
A
Peak low-level output current
(Ta = -40 to 100)
IOPL
(Note 2)
+0.6
Output voltage
VO
35
V
Supply voltage
VCC
35
Junction temperature
Tj
125
Common Operating temperature
Topr
-40 to 100
Storage temperature
Tstg
-55 to 125
Lead soldering temperature
(10 s)
Tsol
260
Isolation voltage
AC, 1 min,
R.H. 60%, Ta = 25
BVS
(Note 3)
3750
Vrms
Note: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the
significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even
if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum
ratings.
Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook
("Handling Precautions"/"Derating Concept and Methods") and individual reliability data (i.e. reliability test
report and estimated failure rate, etc).
Note 1: Pulse width (PW) 1 µs, 300 pps
Note 2: Exponential waveform. Pulse width 2 µs, f 10 kHz, VCC = 20V, Ta = -40 to 100
Note 3: This device is considered as a two-terminal device: Pins 1 and 3 are shorted together, and pins 4, 5 and 6 are
shorted together.
8. Recommended Operating Conditions (Note)
Characteristics
Symbol Note Min Typ. Max Unit
Threshold input current (L/H)
Threshold input voltage (H/L)
Supply voltage
Peak high-level output current
Peak low-level output current
Operating temperature
Operating frequency
IFLH
VFHL
VCC
IOPH
IOPL
Topr
f
(Note 1) 10
0
(Note 2) 10
-40
(Note 3)
15
mA
0.8
V
30
-0.2
A
+0.2
100
250 kHz
Note: The recommended operating conditions are given as a design guide necessary to obtain the intended
performance of the device. Each parameter is an independent value. When creating a system design using
this device, the electrical characteristics specified in this datasheet should also be considered.
Note: A ceramic capacitor (0.1 µF) should be connected between pin 6 and pin 4 to stabilize the operation of a high-
gain linear amplifier. Otherwise, this photocoupler may not switch properly. The bypass capacitor should be
placed within 1 cm of each pin.
Note 1: The rise and fall times of the input on-current should be less than 0.5 µs.
Note 2: Denotes the operating range, not the recommended operating condition.
Note 3: Exponential waveform. IOPH -0.25 A (80 ns), IOPL 0.25 A (80 ns), Ta = 100
3
2012-11-13
Rev.1.0
 

Share Link: 

datasheetbank.com [ Privacy Policy ] [ Request Datasheet ] [ Contact Us ]