datasheetbank_Logo   Integrated circuits, Transistor, Semiconductors Search and Datasheet PDF Download Site
Part Name :   

Y3574 View Datasheet(PDF) - Texas Instruments

Part NameDescriptionManufacturer
Y3574 5-V ANALOG, 3-/5-V DIGITAL, 14-/12-BIT, 200-KSPS, 4-/8-CHANNEL SERIAL ANALOG-TO-DIGITAL CONVERTERS WIRH ±10-V INPUTS TI
Texas Instruments TI
Y3574 Datasheet PDF : 51 Pages
First Prev 21 22 23 24 25 26 27 28 29 30 Next Last
TLC3574, TLC3578, TLC2574, TLC2578
5ĆV ANALOG, 3Ć/5ĆV DIGITAL, 14Ć/12ĆBIT, 200ĆKSPS, 4Ć/8ĆCHANNEL
SERIAL ANALOGĆTOĆDIGITAL CONVERTERS WITH ±10ĆV INPUTS
SLAS262C − OCTOBER 2000 − REVISED MAY 2003
conversion mode (continued)
SWEEP Mode (Mode 10): During each operation, all of the channels listed in the SWEEP SEQUENCE (D[4:3]
of CFR register) are sampled and converted one time according to the programmed sequence. The results are
stored in the FIFO. When the FIFO threshold is reached, an interrupt (INT) is generated, and the operation ends.
If the FIFO threshold is reached before all of the listed channels are visited, the remaining channels are ignored.
This allows the host to change the sweep sequence length. The mode 10 operation starts with the WRITE CFR
command to set the sweep sequence. The following triggers (CS, FS, or CSTART, depending on the interface)
start the samplings and conversions of the listed channels in sequence until the FIFO threshold is hit. If CS or
FS starts the sampling, the SDI data must be any one of the SELECT commands to set the converter in
conversion state. However, this command is a dummy code. It does not change the existing conversion
sequence. After the FIFO is full, the converter waits for FIFO READ. It does nothing before the FIFO READ or
WRITE CFR command is issued. The host must read the FIFO completely or WRITE CFR. If CSTART triggers
the samplings, the host must issue an extra SELECT/CONVERSION command (select any channel) via CS or
FS after the FIFO READ or WRITE CFR. This extra period is named the arm period and is used to set the
converter into conversion state, but does not affect the existing conversion sequence. If FS initiates the
operation and CSTART triggers the samplings and conversions, CS must not toggle during the conversion.
REPEAT SWEEP Mode (Mode 11): This mode works in the same way as mode 10, except that it is not
necessary to read the FIFO before the next operation after the FIFO threshold is hit. The next sweep can repeat
immediately, but the contents in the FIFO are replaced by the new results. The host can read the FIFO
completely, then issue next SWEEP; or repeat the SWEEP immediately (with the existing sweep sequence) by
issuing sampling/conversion triggers (CS, FS or CSTART); or change the device setting with the WRITE CFR
command.
The memory effect of charge redistribution DAC exists when the mux switches from one channel to another.
This degrades the channel-to-channel isolation if the channel changes after each conversion. For example, in
mode 10 and 11, the isolation is about 70 dB for the sweep sequence 0-1-2-3-4. The memory effect can be
reduced by increasing the sampling time or using sweep sequence 0-0-2-2-4-4-6-6 and ignoring the first sample
of each channel.
24
WWW.TI.COM
Direct download click here
 

Share Link : TI
All Rights Reserved © datasheetbank.com 2014 - 2019 [ Privacy Policy ] [ Request Datasheet ] [ Contact Us ]