datasheetbank_Logo   Integrated circuits, Transistor, Semiconductors Search and Datasheet PDF Download Site
Part Name :   

TEA1102T View Datasheet(PDF) - Philips Electronics

Part NameDescriptionManufacturer
TEA1102T Fast charge ICs for NiCd, NiMH, SLA and LiIon Philips
Philips Electronics Philips
TEA1102T Datasheet PDF : 28 Pages
1 2 3 4 5 6 7 8 9 10 Next Last
Philips Semiconductors
Fast charge ICs for NiCd, NiMH, SLA and
LiIon
Preliminary specification
TEA1102; TEA1102T;
TEA1102TS
To ensure an eventual load during all charging states, the
fast charge mode will be entered again if the battery
voltage drops below 15 V for SLA or 3 V for Lilon.
When charging, the standby mode (LiIon and SLA) can
only be entered after a certain period of time depending on
time-out. The same applies for charging NiCd or NiMH
batteries. To support full test of the TEA1102x at
application, the standby mode is also entered when
Vbat < Vbat(l) at fill-up or top-off respectively.
Timer
The timing of the circuit is controlled by the oscillator
frequency.
The timer block defines the maximum charging time by
‘time-out’. At a fixed oscillator frequency, the time-out time
can be adapted by the Programmable Time-out Divider
(PTD) using the following equation.
ttime out = 226 × POD × PTD × tosc
(6)
The time-out timer is put on hold by low voltage,
temperature protection and during the inhibit mode.
The Programmable Oscillator Divider (POD) enables the
oscillator frequency to be increased without affecting
the sampling time and time-out. Raising the oscillator
frequency will reduce the size of the inductive components
that are used.
At fast charging, after battery insertion, after refresh or
supply interruption, the full detector will be disabled for a
period of time to allow a proper start with flat or inverse
polarized batteries. This hold-off period is disabled at fast
charging by raising pin Vstb to above ±5 V (once).
So for test options it is possible to slip the hold-off period.
The hold-off time is defined by the following equation:
thold off = 25 × ttime out
(7)
Table 2 gives an overview of the settings of timing and
discharge/charge currents.
Table 2 Timing and current formulae
SYMBOL
tosc
Tsampling (T/t)
Tsampling (Vpeak)
ttop-off
ttime-out
thold-off
tLED
tsense
tswitch
Ifast
DESCRIPTION
timing
NTC voltage sampling frequency
battery voltage sampling frequency
inhibit or protection
charge/discharge currents
Itop-off
Itrickle
Iload-max
IRFSH
FORMULAE
see Fig.3
217 × POD × PSD × tosc
216 × POD × tosc
227 × POD × tosc
226 × POD × PTD × tosc
25 × ttime-out
214 × POD × tosc
210 × POD × tosc
221 × POD × PTD × tosc
R-----s-R--e---bn--s---e- × R-V----rr--ee--ff
R-----s-R--e---bn--s---e- × 3 × 106
R-----s-R--e---bn--s---e- × 11----56-- × 106
R-----s-R--e---bn--s---e- × 40 × 106
1--R--0--s-0--e---nm---s--Ve---
1999 Jan 27
9
Direct download click here
 

Share Link : Philips
All Rights Reserved © datasheetbank.com 2014 - 2019 [ Privacy Policy ] [ Request Datasheet ] [ Contact Us ]