datasheetbank_Logo
Integrated circuits, Transistor, Semiconductors Search and Datasheet PDF Download Site

TEA1068 View Datasheet(PDF) - Philips Electronics

Part Name
Description
View to exact match
TEA1068 Datasheet PDF : 24 Pages
1 2 3 4 5 6 7 8 9 10 Next Last
Philips Semiconductors
Versatile telephone transmission circuit
with dialler interface
Product specification
TEA1068
FUNCTIONAL DESCRIPTION
Supplies: VCC, LN, SLPE, REG and STAB
Power for the TEA1068 and its peripheral circuits is usually
obtained from the telephone line. The TEA1068 develops
its own supply at VCC and regulates its voltage drop. The
supply voltage VCCmay also be used to supply external
circuits, e.g. dialling and control circuits.
Decoupling of the supply voltage is performed by a
capacitor between VCC and VEE; the internal voltage
regulator is decoupled by a capacitor between REG and
VEE.
The DC current flowing into the set is determined by the
exchange voltage (Vexch), the feeding bridge resistance,
(Rexch) and the DC resistance of the telephone line (Rline).
An internal current stabilizer is set by a resistor of 3.6 k
between the current stabilizer pin STAB and VEE
(see Fig.9).
If the line current Iline exceeds the current ICC+ 0.5 mA
required by the circuit itself (approximately 1 mA) plus the
current Ip required by the peripheral circuits connected to
VCC, then the voltage regulator diverts the excess current
via LN.
The regulated voltage on the line terminal (VLN) can be
calculated as:
VLN = Vref + I SLPE× R9
or
VLN= Vref + [(IlineICC 0.5 × 103) Ip] × R9
where Vref is an internally generated temperature
compensated reference voltage of 4.2 V and R9 is an
external resistor connected between SLPE and VEE.
The preferred value for R9 is 20 . Changing the value of
R9 will also affect microphone gain, DTMF gain, gain
control characteristics, side-tone level, the maximum
output swing on LN and the DC characteristics (especially
at lower voltages).
Under normal conditions, when ISLPE >> ICC + 0.5 mA + Ip,
the static behaviour of the circuit is that of a 4.2 V regulator
diode with an internal resistance equal to that of R9. In the
audio frequency range, the dynamic impedance is largely
determined by R1 (see Fig.4).
The internal reference voltage can be adjusted by means
of an external resistor (RVA). This resistor, connected
between LN and REG, will decrease the internal reference
voltage; when connected between REG and SLPE, it will
increase the internal reference voltage. Current (Ip)
available from VCC for supplying peripheral circuits
depends on external components and on the line current.
Figure 10 shows this current for VCC > 2.2 V and for
VCC> 3 V, this being the minimum supply voltage for most
CMOS circuits, including voltage drop for an enable diode.
If MUTE is LOW, the available current is further reduced
when the receiving amplifier is driven.
handbook, halfpagLeN
VEE
Leq
Rp
R1
Vref
REG
VCC
R9
C3
C1
20
4.7 µF
100 µF
MBA454
Rp = 17.5 k
Leq = C3 × R9 × Rp
Fig.4 Equivalent impedance circuit.
Microphone inputs MIC+ and MICand gain
adjustment pins GAS1 and GAS2
The TEA1068 has symmetrical microphone inputs.
Its input impedance is 64 k(2 × 32 k) and its voltage
gain is typically 52 dB (when R7 = 68 k; see Fig.14).
Dynamic, magnetic, piezoelectric or electret (with built-in
FET source followers) microphones can be used.
The arrangements with the microphone types mentioned
are shown in Fig.11.
The gain of the microphone amplifier can be adjusted
between 44 dB and 60 dB. The gain is proportional to the
value of the external resistor R7 connected between GAS1
and GAS2. An external capacitor C6 of 100 pF between
GAS1 and SLPE is required to ensure stability. A larger
value may be chosen to obtain a first-order low-pass filter.
The cut-off frequency corresponds with the time constant
R7 × C6.
1996 Apr 23
5
 

Share Link: 

datasheetbank.com [ Privacy Policy ] [ Request Datasheet ] [ Contact Us ]