datasheetbank_Logo
Integrated circuits, Transistor, Semiconductors Search and Datasheet PDF Download Site

TDA8358J/N1 View Datasheet(PDF) - Philips Electronics

Part Name
Description
View to exact match
TDA8358J/N1 Datasheet PDF : 20 Pages
1 2 3 4 5 6 7 8 9 10 Next Last
Philips Semiconductors
Full bridge vertical deflection output circuit
in LVDMOS with east-west amplifier
Product specification
TDA8358J
SYMBOL
PARAMETER
CONDITIONS
MIN. TYP. MAX. UNIT
Flyback switch
Io(peak)
Vloss(FB)
maximum (peak) output current
voltage loss at flyback
t 1.5 ms
note 11
Io = 1.1 A
Io = 1.6 A
±1.8 A
7.5 8.5 V
8
9
V
Guard circuit
VO(grd)
guard output voltage
VO(grd)(max) allowable guard voltage
IO(grd)
output current
IO(grd) = 100 µA
5
6
7
V
maximum leakage current
18
V
IL(max) = 10 µA
VO(grd) = 0 V; not active
10
µA
VO(grd) = 4.5 V; active
1
2.5 mA
East-west amplifier
Vo
Vloss
VI(bias)
II(bias)
output voltage
voltage loss
input bias voltage
input bias current
Gv(ol)
THD
open-loop voltage gain
harmonic distortion
at pin OUTEW
Io = 750 mA; note 12
into pin INEW; note 13
Io = 100 mA
Io = 500 mA
68
V
5
V
2
2.5 3.2 V
2.5
µA
11.5
µA
30
dB
0.5 1
%
f3dB(h)
high 3 dB cut-off frequency
1
MHz
Notes
1. To limit VOUTA to 68 V, VFB must be 66 V due to the voltage drop of the internal flyback diode between pins OUTA
and VFB at the first part of the flyback.
2. Allowable input range for both inputs: VI(bias) + Vi(dif)(peak) < 1600 mV and VI(bias) Vi(dif)(peak) > 100 mV.
3. This value specifies the sum of the voltage losses of the internal current paths between pins VP and OUTA, and
between pins OUTB and GND. Specified for Tj = 125 °C. The temperature coefficient for Vloss(1) is a positive value.
4. This value specifies the sum of the voltage losses of the internal current paths between pins VP and OUTB, and
between pins OUTA and GND. Specified for Tj = 125 °C. The temperature coefficient for Vloss(2) is a positive value.
5. The linearity error is measured for a linear input signal without S-correction and is based on the ‘on screen’
measurement principle. This method is defined as follows. The output signal is divided in 22 successive equal time
parts. The 1st and 22nd parts are ignored, and the remaining 20 parts form 10 successive blocks k. A block consists
of two successive parts. The voltage amplitudes are measured across RM, starting at k = 1 and ending at k = 10,
where Vk and Vk+1 are the measured voltages of two successive blocks. Vmin, Vmax and Vavg are the minimum,
maximum and average voltages respectively. The linearity errors are defined as:
a) LE = -V----k---V----a-V--v--gk----+---1- × 100% (adjacent blocks)
b) LE = V-----m----a-V--x--a---v---gV----m----i--n- × 100% (non adjacent blocks)
1999 Dec 22
8
 

Share Link: 

datasheetbank.com [ Privacy Policy ] [ Request Datasheet ] [ Contact Us ]