datasheetbank_Logo
Integrated circuits, Transistor, Semiconductors Search and Datasheet PDF Download Site

TDA8351AQ/N5 View Datasheet(PDF) - Philips Electronics

Part Name
Description
View to exact match
TDA8351AQ/N5
Philips
Philips Electronics Philips
TDA8351AQ/N5 Datasheet PDF : 16 Pages
1 2 3 4 5 6 7 8 9 10 Next Last
Philips Semiconductors
DC-coupled vertical deflection output
circuit
Product specification
TDA8351AQ
PINNING
SYMBOL
Idrive(pos)
Idrive(neg)
VI(fb)
VP
VO(B)
n.c.
GND
VFB
VO(A)
VO(guard)
n.c.
n.c.
n.c.
PIN
DESCRIPTION
1 input power-stage (positive);
includes II(sb) signal bias
2 input power-stage (negative);
includes II(sb) signal bias
3 input feedback voltage
4 supply voltage
5 output voltage B
6 not connected
7 ground
8 input flyback supply voltage
9 output voltage A
10 guard output voltage
11 not connected
12 not connected
13 not connected
handbook, halfpage
I drive(pos) 1
I drive(neg) 2
VI(fb) 3
Vp 4
VO(B) 5
n.c. 6
GND 7 TDA8351A
VFB 8
VO(A) 9
VO(guard) 10
n.c. 11
n.c. 12
n.c. 13
MGC056
The die has been glued to the metal block of the package. If the metal
block is not insulated from the heat sink, the heat sink may only be
connected directly to pin 7.
Fig.2 Pin configuration.
FUNCTIONAL DESCRIPTION
The vertical driver circuit is a bridge configuration. The
deflection coil is connected between the output amplifiers,
which are driven in opposite phase. An external resistor
(RM) connected in series with the deflection coil provides
internal feedback information. The differential input circuit
is voltage driven. The input circuit has been adapted to
enable it to be used with the TDA9150, TDA9151B,
TDA9160A, TDA9162, TDA8366 and TDA8367 which
deliver symmetrical current signals. An external resistor
(RCON) connected between the differential input
determines the output current through the deflection coil.
The relationship between the differential input current and
the output current is defined by: Idiff × RCON = Icoil × RM.
The output current is adjustable from 0.5 A (p-p) to 3 A
(p-p) by varying RM. The maximum input differential
voltage is 1.8 V. In the application it is recommended that
Vdiff = 1.5 V (typ). This is recommended because of the
spread of input current and the spread in the value of
RCON.
The flyback voltage is determined by an additional supply
voltage VFB. The principle of operating with two supply
voltages (class G) makes it possible to fix the supply
voltage VP optimum for the scan voltage and the second
supply voltage VFB optimum for the flyback voltage. Using
this method, very high efficiency is achieved.
The supply voltage VFB is almost totally available as
flyback voltage across the coil, this being possible due to
the absence of a decoupling capacitor (not necessary,
due to the bridge configuration). Built-in protections are:
thermal protection
short-circuit protection of the output pins (pins 5 and 9)
short-circuit protection of the output pins to VP.
A guard circuit VO(guard) is provided. The guard circuit is
activated at the following conditions:
during flyback
during short-circuit of the coil and during short-circuit of
the output pins (pins 5 and 9) to VP or ground
during open loop
when the thermal protection is activated.
This signal can be used for blanking the picture tube
screen.
1999 Sep 27
4
 

Share Link: 

datasheetbank.com [ Privacy Policy ] [ Request Datasheet ] [ Contact Us ]