A1806AA4 View Datasheet(PDF) - Teccor Electronics
Part Name
Description
View to exact match
A1806AA4 Datasheet PDF : 212 Pages
| |||
Multiport Balanced SIDACtor Device
Multiport Balanced SIDACtor Device
1
6 This multiport balanced protector is a surface mount alternative to the modified TO-220
package. It is based on a six-pin surface mount SOIC package and uses Teccor’s
2
5 patented “Y” (US Patent 4,905,119) configuration. It is available in surge current ratings up
to 500 A.
3
4
SIDACtor devices are used to enable equipment to meet various regulatory requirements
including GR 1089, ITU K.20, K.21, and K.45, IEC 60950, UL 60950, and TIA-968 (formerly
known as FCC Part 68).
Electrical Parameters — Symmetrical
Part
Number *
P1556U_
P1806U_
P2106U_
P2356U_
P2706U_
P3206U_
P3406U_
P5106U_
VDRM
Volts
VS
Volts
Pins 1-2, 2-3, 1-3
130
180
150
210
170
250
200
270
230
300
270
350
300
400
420
600
VDRM
Volt
VS
Volts
Pins 4-5, 5-6, 4-6
130
180
150
210
170
250
200
270
230
300
270
350
300
400
420
600
VT
Volts
8
8
8
8
8
8
8
8
IDRM
µAmps
5
5
5
5
5
5
5
5
IS
mAmps
800
800
800
800
800
800
800
800
IT
Amps
2.2
2.2
2.2
2.2
2.2
2.2
2.2
2.2
IH
mAmps
150
150
150
150
150
150
150
150
CO
pF
Pins 3-2, 6-5, 1-2, 4-5
50
50
40
40
40
40
40
40
Electrical Parameters — Asymmetrical
VDRM
Volts
VS
Volts
VDRM
Volt
VS
Volts
Part
Pins 1-2, 2-3, 4-5,
VT
IDRM
IS
IT
IH
CO
Number *
5-6
Pins 4-6, 1-3
Volts µAmps mAmps Amps mAmps
pF
A2106U_6 170
250
50
80
3.5
5
800
2.2
120
40
A5030U_6 400
550
270
350
3.5
5
800
2.2
150
30
* For individual “UA”, “UB”, and “UC” surge ratings, see table below.
General Notes:
• All measurements are made at an ambient temperature of 25 °C. IPP applies to -40 °C through +85 °C temperature range.
• IPP is a repetitive surge rating and is guaranteed for the life of the product.
• Listed SIDACtor devices are bi-directional. All electrical parameters and surge ratings apply to forward and reverse polarities.
• VDRM is measured at IDRM.
• VS is measured at 100 V/µs.
• Special voltage (VS and VDRM) and holding current (IH) requirements are available upon request.
• Off-state capacitance is measured between Pins 1-2 and 3-2 at 1 MHz with a 2 V bias and is a typical value for “UA” product. “UB”
and “UC” capacitance is approximately 10 pF higher.
• Device is designed to meet balance requirements of GTS 8700 and GR 974.
Surge Ratings
Series
A
B
C
IPP
2x10 µs
Amps
150
250
500
IPP
8x20 µs
Amps
150
250
400
IPP
10x160 µs
Amps
90
150
200
IPP
10x560 µs
Amps
50
100
150
IPP
10x1000 µs
Amps
45
80
100
ITSM
60 Hz
Amps
20
30
50
di/dt
Amps/µs
500
500
500
http://www.teccor.com
+1 972-580-7777
2 - 24
© 2002 Teccor Electronics
SIDACtor® Data Book and Design Guide
|
|
Share Link: 