EF6805U3FND View Datasheet(PDF) - STMicroelectronics

Part Name

Description

View to exact match

EF6805U3FND

8-BIT MICROCOMPUTER UNIT

STMicroelectronics 

EF6805U3

Half Carry (H) - Set during ADD and ADC operations

to indicate that a carry occurred between bits 3 and

4.

Interrupt (I) - When this bit is set, the timer an exter-

nal interrupts (INT and INT2) are masked (disabled).

If an interrupt occurs while this bit is set, the interrupt

is latched and is processed as soon as the interrupt

bit is cleared.

Negative (N) - When set, this bit indicates that the

result of the last arithmetic, logical, or data manipu-

lation was negative (bit 7 in the result is a logical "1").

Zero (Z) - When set, this bit indicates that the result

of the last arithmetic, logical, or data manipulation

was zero.

Carry/Borrow (C) - When set, this bit indicates that

a carry or borrow ou of the Arithmetic Logic Unit

(ALU) occurred during the last arithmetic operation.

This bit is also affected during bit test and branch in-

structions plus shifts and rotates.

TIMER

The timer circuitry for the EF6805U3 is shown in fig-

ure 10. The timer contains a single 8-bit software

programmable counter with a 7-bit software selec-

table prescaler. The counter may be preset under

program control and decrements toward zero.

When the counter decrements to zero, the timer in-

terrupt request bit, i.e., bit 7 of the timer control re-

gister (TCR), is set. Then if the timer interrupt is not

masked, i.e.,bit 6 of the TCR and the I bit in the

condition code register are both cleared, the proces-

sor receives an interrupt. After completion of the cur-

rent instruction, the processor proceeds to store the

appropriate registers on the stack, and then fetches

the timer interrupt vector from locations $FF8 and

$FF9 in order to begin servicing the interrupt.

The counter continues to count after it reaches zero,

allowing the software to determine the number of in-

ternal or external input clocks since the timer inter-

rupt request bit was set. The counter may be read

at any time by the processor without disturbing the

count. The contents of the counter become stable

prior to the read portion of a cycle and do not change

during the read. The timer interrupt request bit re-

mains set until cleared by the software. If a write oc-

curs before the timer interrup is sericed, the interrupt

is lost. TCR7 may also be used as a scanned status

bit in a non-interrupt mode of operation (TCR6 = 1).

The prescaler is a 7-bit divider which is used to ex-

tend the maximum length of the timer. Bit 0, bit 1,

and bit 2 of the TCR are programmed to choose the

appropriate prescaler outptu which is used as the

counter input. The processor cannot writ eijto or

read from the prescaler ; however, its contents are

cleared to all zeros by the write operation into TCR

when bit 3 of the written data equals one, which al-

lows for truncation-free counting.

The timer input can be configured for three different

operating modes, plus a disable mode, depending

on the value written to the TCR4 and TCR5 control

bits. For further information see figure 9.

Timer Input Mode 1 - If TCR5 adn TCR4 are both

programmed to a zero, the inpt to the timer is from

an internal clock and the external TIMER input is di-

sabled. The internal clock mode canbe used for pe-

riodic interrupt generation, as well as a referene in

frequency and event measurement. The internal

clock is the instruction cycle clock.

Timer Input Mode 2 - With TCR5 = 0 and TCR4 =

1, the internal clock and the TIMER input pin are AN-

Ded to form the timer input signal. This mode can be

used to measure external pulse widths. The external

timer input pulse simply turns on the internal clock

for the duration of the pulse widths.

Timer Input Mode 3 - If TCR5 = 1 and TCR4 = 0, then

all inputs to the timer are disabled.

Timer Input Mode 4 - If TCR5 = 1 and TCR4 = 1, the

internal clock input to the timer is disabled and the

TIMER input pin becomes the input to the timer. The

external TIMER pin can, in this mode, be used to

count external events as well as external frequen-

cies for generating periodic interrupts.

TCR7 - Timer Interrupt Request Bit :

7 6 5 4 3 2 10

TCR7 TCR6 TCR5 TCR4 TCR3 TCR2 TCR1 TCR0$009

* Write only (read as zero).

1 - Set when TDR goes to zero, or under pro-

gram control

0 - Cleared on external Reset, Power-On-Re-

set, or under Program Control.

TCR6 - Timer Interrupt Mask Bit :

1 - Timer Interrupt masked (disabled) Set on

external Reset, Power-On-Reset, or under

Program Control

0 - Cleared under Program Control.

TCR5 - External or Internal Clock Source Bit :

1 - External Clock Source. Set on external Re-

set, Power-On-Reset, or under Program

Control

0 - Cleared under Program Control.

TCR4 - External Enable Bit :

1 - Enable external TIMER pin. Set on external

Reset, Poxer-On-Reset, or under Program

8/31

Share Link: