datasheetbank_Logo    Integrated circuits, Transistor, Semiconductors Search and Datasheet PDF Download Site
Part Name :

DP83815 View Datasheet(PDF) - National ->Texas Instruments

Part NameDP83815 National-Semiconductor
National ->Texas Instruments National-Semiconductor
Description10/100 Mb/s Integrated PCI Ethernet Media Access Controller and Physical Layer (MacPhyter™)
DP83815 Datasheet PDF : 108 Pages
First Prev 31 32 33 34 35 36 37 38 39 40 Next Last
4.0 Register Set (Continued)
4.1.6 Configuration Memory Address Register
This register specifies the Base Memory address which is required to build an address map during configuration. It also
specifies the number of bytes required as well as an indication that it can be mapped into memory space.
Tag: CFGMA
Offset: 14h
Size: 32 bits
Access: Read Write
Hard Reset: 00000000h
Soft Reset: unchanged
Bit
31-12
11-4
3
2-1
0
Bit Name
Description
MEMBASE Memory Base Address
This is set by software to the base address for the Operational Register Map.
MEMSIZE Memory Size
These bits return 0, which indicates that the DP83815 requires 4096 bytes of Memory Space (the
minimum recommended allocation).
MEMPF Prefetchable
Set to 0 by DP83815. Read Only.
MEMLOC Location Selection
Set to 00 by DP83815. This indicates that the base register is 32-bits wide and can be placed anywhere
in the 32-bit memory space. Read Only.
MEMIND Memory Space Indicator
Set to 0 by DP83815 to indicate that DP83815 is capable of being mapped into memory space. Read
Only.
4.1.7 Configuration Subsystem Identification Register
The CFGSID allows system software to distinguish between different subsystems based on the same PCI silicon. The
values in this register can be loaded from the EEPROM if configuration is enabled.
Tag: CFGSID
Offset: 2Ch
Size: 32 bits
Access: Read Only
Hard Reset: 00000000h
Soft Reset: unchanged
Bit
31-16
15-0
Bit Name
SDEVID
SVENID
Subsystem Device ID
Set to 0 by DP83815.
Subsystem Vendor ID
Set to 0 by DP83815.
Description
36
www.national.com
Direct download click here
 

General Description
DP83815 is a single-chip 10/100 Mb/s Ethernet Controller for the PCI bus. It is targeted at low-cost, high volume PC mother boards, adapter cards, and embedded systems. The DP83815 fully implements the V2.2 33 MHz PCI bus interface for host communications with power management support. Packet descriptors and data are transferred via bus-mastering, reducing the burden on the host CPU. The DP83815 can support full duplex 10/100 Mb/s transmission and reception, with minimum interframe gap.
The DP83815 device is an integration of an enhanced version of the National Semiconductor PCI MAC/BIU (Media Access Controller/Bus Interface Unit) and a 3.3V CMOS physical layer interface.

Features
— IEEE 802.3 Compliant, PCI V2.2 MAC/BIU supports traditional data rates of 10 Mb/s Ethernet and 100 Mb/s Fast Ethernet (via internal phy)
— Bus master - burst sizes of up to 128 dwords (512 bytes)
— BIU compliant with PC 97 and PC 98 Hardware Design Guides, PC 99 Hardware Design Guide draft, ACPI v1.0, PCI Power Management Specification v1.1, OnNow Device Class Power Management Reference Specification - Network Device Class v1.0a
— Wake on LAN (WOL) support compliant with PC98,
PC99, SecureOn, and OnNow, including directed
packets, Magic Packet, VLAN packets, ARP packets,
pattern match packets, and Phy status change
— Clkrun function for PCI Mobile Design Guide
— Virtual LAN (VLAN) and long frame support
— Support for IEEE 802.3x Full duplex flow control
— Extremely flexible Rx packet filtration including: single address perfect filter with MSb masking, broadcast, 512 entry multicast/unicast hash table, deep packet pattern matching for up to 4 unique patterns
— Statistics gathered for support of RFC 1213 (MIB II),
RFC 1398 (Ether-like MIB), IEEE 802.3 LME, reducing
CPU overhead for management
— Internal 2 KB Transmit and 2 KB Receive data FIFOs
— Serial EEPROM port with auto-load of configuration data from EEPROM at power-on
— Flash/PROM interface for remote boot support
— Fully integrated IEEE 802.3/802.3u 3.3V CMOS physical layer
— IEEE 802.3 10BASE-T transceiver with integrated filters
— IEEE 802.3u 100BASE-TX transceiver
— Fully integrated ANSI X3.263 compliant TP-PMD physical sublayer with adaptive equalization and Baseline Wander compensation
— IEEE 802.3u Auto-Negotiation - advertised features configurable via EEPROM
— Full Duplex support for 10 and 100 Mb/s data rates
— Single 25 MHz reference clock
— 144-pin LQFP and 160-pin LBGA packages
— Low power 3.3V CMOS design with typical consumption of 561 mW operating, 380 mW during WOL mode, 33 mW sleep mode
— IEEE 802.3u MII for connecting alternative external Physical Layer Devices

Share Link : National-Semiconductor
All Rights Reserved © datasheetbank.com 2014 - 2018 [ Privacy Policy ] [ Request Datasheet ] [ Contact Us ]