NB6L295MNG View Datasheet(PDF) - ON Semiconductor

Part Name

Description

View to exact match

NB6L295MNG

2.5V / 3.3V Dual Channel Programmable Clock/Data Delay with Differential CML Outputs

ON Semiconductor 

NB6L295

Table 4. DC CHARACTERISTICS, MULTI−LEVEL INPUTS VCC = VCC0 = VCC1 = 2.375 V to 3.6 V, GND = 0 V, TA = −40°C to

+85°C

Symbol

Characteristic

Min

Typ

Max

Unit

POWER SUPPLY CURRENT

ICC

Power Supply Current (Inputs, VTx and Outputs Open) (Sum of ICC,

110

140

170

mA

ICC0, and ICC1)

LVPECL OUTPUTS (Notes 5 and 6, Figure 21)

VOH

Output HIGH Voltage

VCC − 1075 VCC − 950 VCC − 825

mV

VCC = VCC0 = VCC1 = 3.3 V

2225

2350

2475

VCC = VCC0 = VCC1 = 2.5 V

1425

1550

1675

VOL

Output LOW Voltage

VCC − 1825 VCC − 1725 VCC − 1625

mV

VCC = VCC0 = VCC1 = 3.3 V

1475

1575

1675

VCC − 1825 VCC − 1725 VCC − 1600

VCC = VCC0 = VCC1 = 2.5 V

675

775

900

DIFFERENTIAL INPUT DRIVEN SINGLE−ENDED (see Figures 10 and 11) (Note 7)

Vth

Input Threshold Reference Voltage Range

1050

VIH

Single−Ended Input HIGH Voltage

Vth + 150

VIL

Single−Ended Input LOW Voltage

GND

VISE

Single−Ended Input Voltage Amplitude (VIH − VIL)

300

DIFFERENTIAL INPUTS DRIVEN DIFFERENTIALLY (see Figures 12 and 13) (Note 8)

VCC − 150

mV

VCC

mV

Vth − 150

mV

VCC − GND

mV

VIHD

Differential Input HIGH Voltage

VILD

Differential Input LOW Voltage

VID

Differential Input Voltage Swing (INx, INx) (VIHD − VILD)

VCMR Input Common Mode Range (Differential Configuration) (Note 9)

IIH

Input HIGH Current INx/INx, (VTn/VTn Open)

IIL

Input LOW Current IN/INX, (VTn/VTn Open)

SINGLE−ENDED LVCMOS/LVTTL CONTROL INPUTS

1200

GND

150

950

−150

−150

VCC

mV

VCC − 150

mV

VCC − GND

mV

VCC – 75

mV

150

mA

150

mA

VIH

Single−Ended Input HIGH Voltage

VIL

Single−Ended Input LOW Voltage

IIH

Input HIGH Current

IIL

Input LOW Current

TERMINATION RESISTORS

2000

GND

−150

−150

VCC

mV

800

mV

150

mA

150

mA

RTIN

Internal Input Termination Resistor

40

50

60

W

NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit

board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared

operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit

values are applied individually under normal operating conditions and not valid simultaneously.

5. LVPECL outputs loaded with 50 W to VCC − 2.0 V for proper operation.

6. Input and output parameters vary 1:1 with VCC.

7. Vth, VIH, VIL,, and VISE parameters must be complied with simultaneously. Vth is applied to the complementary input when operating in

single−ended mode.

8. VIHD, VILD, VID and VCMR parameters must be complied with simultaneously.

9. VCMR(min) varies 1:1 with voltage on GND Pin, VCMR(max) varies 1:1 with VCC. The VCMR range is referenced to the most positive side

of the differential input signal.

http://onsemi.com

5

Share Link: