datasheetbank_Logo
Integrated circuits, Transistor, Semiconductors Search and Datasheet PDF Download Site

N08L1618C2AB2 View Datasheet(PDF) - NanoAmp Solutions, Inc.

Part Name
Description
View to exact match
N08L1618C2AB2
NANOAMP
NanoAmp Solutions, Inc. NANOAMP
N08L1618C2AB2 Datasheet PDF : 10 Pages
1 2 3 4 5 6 7 8 9 10
NanoAmp Solutions, Inc.
N08L1618C2A
Advance Information
Absolute Maximum Ratings1
Item
Symbol
Rating
Unit
Voltage on any pin relative to VSS
VIN,OUT
–0.3 to VCC+0.3
V
Voltage on VCC Supply Relative to VSS
VCC
–0.3 to 3.0
V
Power Dissipation
PD
500
mW
Storage Temperature
TSTG
–40 to 125
oC
Operating Temperature
TA
-40 to +85
oC
Soldering Temperature and Time
TSOLDER
260oC, 10sec
oC
1. Stresses greater than those listed above may cause permanent damage to the device. This is a stress rating only and functional
operation of the device at these or any other conditions above those indicated in the operating section of this specification is not
implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability.
Operating Characteristics (Over Specified Temperature Range)
Item
Symbol
Test Conditions
Min.
Typ1
Max Unit
Supply Voltage
VCC
Data Retention Voltage
VDR
Input High Voltage
VIH
Input Low Voltage
VIL
Output High Voltage
VOH
Output Low Voltage
VOL
Input Leakage Current
ILI
Output Leakage Current
ILO
Read/Write Operating Supply Current
@ 1 µs Cycle Time2
ICC1
Read/Write Operating Supply Current
@ 70 ns Cycle Time2
ICC2
Page Mode Operating Supply Current
@ 70 ns Cycle Time2
ICC3
Read/Write Quiescent Operating Sup-
ply Current3
ICC4
Maximum Standby Current3
ISB1
Maximum Data Retention Current3
IDR
Chip Disabled3
IOH = 0.2mA
IOL = -0.2mA
VIN = 0 to VCC
OE = VIH or Chip Disabled
VCC=2.2 V, VIN=VIH or VIL
Chip Enabled, IOUT = 0
VCC=2.2 V, VIN=VIH or VIL
Chip Enabled, IOUT = 0
VCC=2.2 V, VIN=VIH or VIL
Chip Enabled, IOUT = 0
VCC=2.2 V, VIN=VIH or VIL
Chip Enabled, IOUT = 0,
f=0
VIN = VCC or 0V
Chip Disabled
tA= 85oC, VCC = 2.2 V
Vcc = 1.2V, VIN = VCC or 0
Chip Disabled, tA= 85oC
1.65
1.2
0.7VCC
–0.3
VCC–0.2
1.8
1.0
10.0
0.5
0.5
2.2
V
V
VCC+0.3 V
0.3VCC V
V
0.2
V
0.5
µA
0.5
µA
3.0 mA
14.0 mA
3.0 mA
20
µA
20.0 µA
10
µA
1. Typical values are measured at Vcc=Vcc Typ., TA=25°C and not 100% tested.
2. This parameter is specified with the outputs disabled to avoid external loading effects. The user must add current required to drive
output capacitance expected in the actual system.
3. This device assumes a standby mode if the chip is disabled (CE1 high or CE2 low). In order to achieve low standby current all
inputs must be within 0.2 volts of either VCC or VSS.
(DOC#14-02-019 REV F ECN# 01-1280)
3
The specifications of this device are subject to change without notice. For latest documentation see http://www.nanoamp.com.
 

Share Link: 

datasheetbank.com [ Privacy Policy ] [ Request Datasheet ] [ Contact Us ]