datasheetbank_Logo     データシート検索エンジンとフリーデータシート

AM1 データシートの表示(PDF) - WJ Communications => Triquint

部品番号コンポーネント説明メーカー
AM1 High Dynamic Range Gain Block WJ
WJ Communications => Triquint WJ
AM1 Datasheet PDF : 6 Pages
1 2 3 4 5 6
AM1
High Dynamic Range Gain Block
The Communications Edge TM
Product Information
AM1-G (Green / Lead-free SOT-89 Package) Mechanical Information
This package is lead-free/Green/RoHS-compliant. It is compatible with both lead-free (maximum 260 qC reflow temperature) and leaded
(maximum 245 qC reflow temperature) soldering processes. The plating material on the leads is NiPdAu.
Outline Drawing
Land Pattern
Product Marking
The AM1-G will be marked with an “A1G”
designator. An alphanumeric lot code
(“XXXX-X” ) is also marked below the part
designator on the top surface of the package.
A “0 will be lasermarked in the upper right-
hand corner. The obsolete tin-lead package is
marked with an “A1” designator followed by
an alphanumeric lot code.
Tape and reel specifications for this part are
located on the website in the “Application
Notes” section.
MSL / ESD Rating
ESD Rating: Class 1B
Value:
Passes 500V to <1000V
¥
Test:
Human Body Model (HBM)
Standard: JEDEC Standard JESD22-A114
ESD Rating: Class IV
Value:
Passes 1000V to <2000V
¥
Test:
Charged Device Model (CDM)
Standard: JEDEC Standard JESD22-C101
MSL Rating: Level 3 at +260 ¤ C convection reflow
Standard: JEDEC Standard J-STD-020
Thermal Specifications
Parameter
Rating
10000
Operating Case Temperature -40 to +85 qC
MTTF vs. GND Tab Temperature
Mounting Config. Notes
1. Ground / thermal vias are critical for the proper
performance of this device. Vias should use a .35mm
(#80 / .0135” ) diameter drill and have a final plated
thru diameter of .25 mm (.010” ).
Thermal Resistance, Rth (1)
88 qC/W
1000
Junction Temperature, Tj (2)
116 qC
2. Add as much copper as possible to inner and outer
layers near the part to ensure optimal thermal
performance.
1. The thermal resistance is referenced from the hottest
part of the junction to the ground tab (pin 4).
2. This corresponds to the typical biasing condition of
+5V, 78 mA at an 85 C ¤ case temperature. A
minimum MTTF of 1 million hours is achieved for
junction temperatures below 160 ¤ C.
100
10
60
3. Mounting screws can be added near the part to fasten
the board to a heatsink. Ensure that the ground /
thermal via region contacts the heatsink.
4. Do not put solder mask on the backside of the PC board
in the region where the board contacts the heatsink.
70
80
90
100
110
5. RF trace width depends upon the PC board material
and construction.
Tab Temperature (°C)
6. Use 1 oz. Copper minimum.
7. All dimensions are in millimeters (inches). Angles are
in degrees.
Specifications and information are subject to change without notice.
WJ Communications, Inc Phone 1-800-WJ1-4401 FAX: 408-577-6621 e-mail: sales@wj.com Web site: www.wj.com
£
£
£
£
Page 6 of 6 June 2006
Direct download click here

 

Share Link : 

All Rights Reserved © datasheetbank.com 2014 - 2020 [ 個人情報 保護方針 ] [ リクエストデータシート ]