MC100EP32DTR2(2004) View Datasheet(PDF) - ON Semiconductor
Part Name
Description
View to exact match
MC100EP32DTR2 Datasheet PDF : 10 Pages
| |||
MC10EP32, MC100EP32
Table 10. 100EP DC CHARACTERISTICS, NECL VCC = 0 V; VEE = −5.5 V to −3.0 V (Note 17)
−40°C
25°C
85°C
Symbol
Characteristic
Min Typ Max Min Typ Max Min Typ Max Unit
IEE
VOH
VOL
VIH
VIL
VBB
VIHCMR
Power Supply Current
Output HIGH Voltage (Note 18)
Output LOW Voltage (Note 18)
Input HIGH Voltage (Single−Ended)
Input LOW Voltage (Single−Ended)
Output Voltage Reference
Input HIGH Voltage Common Mode
Range (Differential Configuration)
(Note 19)
23
30
37
26
34
40
28
36
42 mA
−1145 −1020 −895 −1145 −1020 −895 −1145 −1020 −895 mV
−1945 −1820 −1695 −1945 −1820 −1695 −1945 −1820 −1695 mV
−1225
−880 −1225
−880 −1225
−880 mV
−1945
−1625 −1945
−1625 −1945
−1625 mV
−1525 −1425 −1325 −1525 −1425 −1325 −1525 −1425 −1325 mV
VEE+2.0
0.0
VEE+2.0
0.0
VEE+2.0
0.0 V
IIH
Input HIGH Current
IIL
Input LOW Current
150
150
150 mA
0.5
0.5
0.5
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
17. Input and output parameters vary 1:1 with VCC.
18. All loading with 50 W to VCC − 2.0 V.
19. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential
input signal.
Table 11. AC CHARACTERISTICS VCC = 0 V; VEE = −3.0 V to −5.5 V or VCC = 3.0 V to 5.5 V; VEE = 0 V (Note 20)
−40°C
25°C
85°C
Symbol
Characteristic
Min Typ Max Min Typ Max Min Typ Max Unit
VOPP
Output Voltage Amplitude
(See Figure 3)
fin < 3.5 GHz
700
fin @ 4.0 GHz 640 740
700
630 710
mV
700
500 600
tPLH,
tPHL
Propagation Delay to
Output Differential
10 Series
100 Series
ps
CLK to Q, Q 250 330 420 270 350 450 320 400 480
RESET to Q, Q 220 290 390 250 300 390 320 380 460
RESET to Q, Q 320 400 480 320 400 480 375 450 525
tRR
Set/Reset Recovery
200
tPW
Minimum Pulse width
RESET 550
tJITTER
CLOCK Random Jitter (RMS)
fin < 3.5 GHz
fin @ v4.0 GHz
VPP
Input Voltage Swing
150
(Differential Configuration)
175
200
475
550
0.5
0.5 1.5
800 1200 150
175
200
475
550
0.5
0.5 1.5
800 1200 150
175
ps
475
ps
ps
0.5
0.5 1.5
800 1200 mV
tr
Output Rise/Fall Times
tf
(20% − 80%)
Q, Q 50 100 150 70 120 170 70 130 200 ps
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
20. Measured using a 750 mV source, 50% duty cycle clock source. All loading with 50 W to VCC − 2.0 V.
http://onsemi.com
6
|
|
Share Link: 