MC100EP16TDG View Datasheet(PDF) - ON Semiconductor
Part Name
Description
View to exact match
MC100EP16TDG Datasheet PDF : 11 Pages
| |||
MC10EP16T, MC100EP16T
Table 3. MAXIMUM RATINGS
Symbol
Parameter
Condition 1
Condition 2
Rating
Unit
VCC
PECL Mode Power Supply
VEE
NECL Mode Power Supply
VI
PECL Mode Input Voltage
NECL Mode Input Voltage
Iout
Output Current
VEE = 0 V
VCC = 0 V
VEE = 0 V
VCC = 0 V
Continuous
Surge
VI v VCC
VI w VEE
6
V
−6
V
6
V
−6
V
50
mA
100
mA
IBB
VBB Sink/Source
TA
Operating Temperature Range
Tstg
Storage Temperature Range
qJA
Thermal Resistance (Junction−to−Ambient)
0 lfpm
500 lfpm
SOIC−8
SOIC−8
± 0.5
−40 to +85
−65 to +150
190
130
mA
°C
°C
°C/W
°C/W
qJC
Thermal Resistance (Junction−to−Case)
Standard Board
qJA
Thermal Resistance (Junction−to−Ambient)
0 lfpm
500 lfpm
SOIC−8
TSSOP−8
TSSOP−8
41 to 44
185
140
°C/W
°C/W
°C/W
qJC
Thermal Resistance (Junction−to−Case)
Standard Board
qJA
Thermal Resistance (Junction−to−Ambient)
0 lfpm
500 lfpm
TSSOP−8
DFN8
DFN8
41 to 44
129
84
°C/W
°C/W
°C/W
Tsol
Wave Solder
Pb
Pb−Free
265
°C
265
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
Table 4. 10EP DC CHARACTERISTICS, PECL VCC = 3.3 V, VEE = 0 V (Note 2)
−40°C
25°C
85°C
Symbol
Characteristic
Min Typ Max Min Typ Max Min Typ Max Unit
IEE
Power Supply Current
16 23 31 16 23 31 16 23 31 mA
VOH
Output HIGH Voltage (Note 3)
2165 2290 2415 2230 2355 2480 2290 2415 2540 mV
VOL
Output LOW Voltage (Note 3)
1365 1490 1615 1430 1555 1680 1490 1615 1740 mV
VIH
Input HIGH Voltage (Single−Ended)
2090
2415 2155
2480 2215
2540 mV
VIL
Input LOW Voltage (Single−Ended)
1365
1690 1430
1755 1490
1815 mV
VIHCMR Input HIGH Voltage Common Mode Range 2.0
(Differential Configuration) (Note 4)
3.3 2.0
3.3 2.0
3.3
V
RT
Internal Termination Resistor
IIH
Input HIGH Current
IIL
Input LOW Current
43
−150
57 43 50
150
−150
57 43
150
−150
57
W
150 mA
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
2. Input and output parameters vary 1:1 with VCC. VEE can vary +0.3 V to −2.2 V.
3. All loading with 50 W to VCC − 2.0 V.
4. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential
input signal.
http://onsemi.com
3
|
|
Share Link: 