MC100EL35DTG View Datasheet(PDF) - ON Semiconductor
Part Name
Description
View to exact match
MC100EL35DTG Datasheet PDF : 7 Pages
| |||
MC10EL35, MC100EL35
Table 6. 100EL SERIES NECL DC CHARACTERISTICS (VCC = 0 V; VEE = −5.0 V (Note 1))
−40°C
25°C
85°C
Symbol
Characteristic
Min Typ Max Min Typ Max Min Typ Max Unit
IEE
Power Supply Current
VOH
Output HIGH Voltage (Note 2)
VOL
Output LOW Voltage (Note 2)
VIH
Input HIGH Voltage (Single-Ended)
VIL
Input LOW Voltage (Single-Ended)
IIH
Input HIGH Current
IIL
Input LOW Current
27
32
27
32
32
37
mA
−1085 −1005 −880 −1025 −955 −880 −1025 −955 −880 mV
−1830 −1695 −1555 −1810 −1705 −1620 −1810 −1705 −1620 mV
−1165
−880 −1165
−880 −1165
−880 mV
−1810
−1475 −1810
−1475 −1810
−1475 mV
150
150
150 mA
0.5
0.5
0.5
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
1. Input and output parameters vary 1:1 with VCC. VEE can vary +0.8 V / −0.5 V.
2. Outputs are terminated through a 50 W resistor to VCC − 2.0 V.-
Table 7. AC CHARACTERISTICS (VCC = 5.0 V; VEE = 0 V or VCC = 0 V; VEE = −5.0 V (Note 1))
−40°C
25°C
85°C
Symbol
Characteristic
Min Typ Max Min Typ Max Min Typ Max Unit
fmax Maximum Toggle Frequency
1.4 2.0
1.8 2.2
1.8 2.2
GHz
tPLH
Propagation Delay
tPHL
to Output
tS
Setup Time
tH
Hold Time
tRR
Reset Recovery
tPW
Minimum Pulse Width
CLK, Reset
CLK
290 515 740 350 525 700 395 570 745 ps
MR
225 450 675 275 450 625 350 525 700
J, K
150
0
150
0
150
0
ps
J, K
250 100
250 100
250 100
ps
400 200
400 200
400 200
ps
400
400
400
ps
tJITTER Cycle-to-Cycle Jitter
1.0
1.0
1.0
ps
tr
Output Rise/Fall Times Q (20%−80%) 100 225 350 100 225 350 100 225 350 ps
tf
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
1. 10 Series: VEE can vary +0.25 V / −0.5 V.
100 Series: VEE can vary +0.8 V / −0.5 V.
www.onsemi.com
4
|
|
Share Link: 