datasheetbank_Logo
Integrated circuits, Transistor, Semiconductors Search and Datasheet PDF Download Site

MBM29F017A View Datasheet(PDF) - Spansion Inc.

Part Name
Description
View to exact match
MBM29F017A
Spansion
Spansion Inc. Spansion
MBM29F017A Datasheet PDF : 49 Pages
First Prev 11 12 13 14 15 16 17 18 19 20 Next Last
MBM29F017A-70/-90/-12
Chip Erase
Chip erase is a six bus cycle operation. There are two “unlock” write cycles. These are followed by writing the
“set-up” command. Two more “unlock” write cycles are then followed by the chip erase command.
Chip erase does not require the user to program the device prior to erase. Upon executing the Embedded EraseTM
Algorithm command sequence the device will automatically program and verify the entire memory for an all zero
data pattern prior to electrical erase. The system is not required to provide any controls or timings during these
operations.
The automatic erase begins on the rising edge of the last WE pulse in the command sequence and terminates
when the data on DQ7 is “1” (See Write Operation Status section.) at which time the device returns to read the
mode.
“Embedded Programming Algorithm” in sFLOW CHART illustrates the Embedded EraseTM Algorithm using
typical command strings and bus operations.
Sector Erase
Sector erase is a six bus cycle operation. There are two “unlock” write cycles. These are followed by writing the
“set-up” command. Two more “unlock” write cycles are then followed by the sector erase command. The sector
address (any address location within the desired sector) is latched on the falling edge of WE, while the command
(Data = 30h) is latched on the rising edge of WE. After time-out of 50 µs from the rising edge of the last sector
erase command, the sector erase operation will begin.
Multiple sectors may be erased concurrently by writing the six bus cycle operations on “MBM29F017A Command
Definitions” in sDEVICE BUS OPERATION. This sequence is followed with writes of the Sector Erase command
to addresses in other sectors desired to be concurrently erased. The time between writes must be less than 50
µs otherwise that command will not be accepted and erasure will start. It is recommended that processor
interrupts be disabled during this time to guarantee this condition. The interrupts can be re-enabled after the
last Sector Erase command is written. A time-out of 50 µs from the rising edge of the last WE will initiate the
execution of the Sector Erase command (s). If another falling edge of the WE occurs within the 50 µs time-out
window the timer is reset. (Monitor DQ3 to determine if the sector erase timer window is still open, see section
DQ3, Sector Erase Timer.) Any commands other than Sector Erase or Erase Suspend during this time-out period
will reset the device to the read mode, ignoring the previous command string. Resetting the device once execution
has begun will corrupt the data in that sector. In that case, restart the erase on those sectors and allow them to
complete. (Refer to the Write Operation Status section for DQ3, Sector Erase Timer operation.) Loading the
sector erase buffer may be done in any sequence and with any number of sectors (0 to 31).
Sector erase does not require the user to program the device prior to erase. The device automatically programs
all memory locations in the sector (s) to be erased prior to electrical erase. When erasing a sector or sectors
the remaining unselected sectors are not affected. The system is not required to provide any controls or timings
during these operations.
The automatic sector erase begins after the 50 µs time out from the rising edge of the WE pulse for the last
sector erase command pulse and terminates when the data on DQ7 is “1” (See Write Operation Status section.)
at which time the device returns to the read mode. Data polling must be performed at an address within any of
the sectors being erased.
“Embedded Programming Algorithm” in sFLOW CHART illustrates the Embedded EraseTM Algorithm using
typical command strings and bus operations.
Erase Suspend
The Erase Suspend command allows the user to interrupt a Sector Erase operation and then perform data reads
from or programs to a sector not being erased. This command is applicable ONLY during the Sector Erase
operation which includes the time-out period for sector erase. The Erase Suspend command will be ignored if
written during the Chip Erase operation or Embedded ProgramTM Algorithm. Writting the Erase Suspend com-
mand during the Sector Erase time-out results in immediate termination of the time-out period and suspension
of the erase operation.
16
 

Share Link: 

datasheetbank.com [ Privacy Policy ] [ Request Datasheet ] [ Contact Us ]