MBM29F016A-12 View Datasheet(PDF) - Fujitsu

Part Name

Description

View to exact match

MBM29F016A-12

FLASH MEMORY CMOS 16M (2M × 8) BIT

Fujitsu 

MBM29F016A-70/-90/-12

s GENERAL DESCRIPTION

The MBM29F016A is a 16 M-bit, 5.0 V-Only Flash memory organized as 2 M bytes of 8 bits each. The 2 M bytes

of data is divided into 32 sectors of 64 K bytes for flexible erase capability. The 8 bit of data will appear on DQ0

to DQ7. The MBM29F016A is offered in a 48-pin TSOP(I) package. This device is designed to be programmed

in-system with the standard system 5.0 V VCC supply. A 12.0 V VPP is not required for program or erase operations.

The device can also be reprogrammed in standard EPROM programmers.

The standard MBM29F016A offers access times between 70 ns and 120 ns allowing operation of high-speed

microprocessors without wait states. To eliminate bus contention the device has separate chip enable (CE), write

enable (WE), and output enable (OE) controls.

The MBM29F016A is command set compatible with JEDEC standard E2PROMs. Commands are written to the

command register using standard microprocessor write timings. Register contents serve as input to an internal

state-machine which controls the erase and programming circuitry. Write cycles also internally latch addresses

and data needed for the programming and erase operations. Reading data out of the device is similar to reading

from 12.0 V Flash or EPROM devices.

The MBM29F016A is programmed by executing the program command sequence. This will invoke the Embedded

Program Algorithm which is an internal algorithm that automatically times the program pulse widths and verifies

proper cell margin. Each sector can be programmed and verified in less than 0.5 seconds. Erase is accomplished

by executing the erase command sequence. This will invoke the Embedded Erase Algorithm which is an internal

algorithm that automatically preprograms the array if it is not already programmed before executing the erase

operation. During erase, the device automatically times the erase pulse widths and verifies proper cell margin.

This device also features a sector erase architecture. The sector erase mode allows for sectors of memory to

be erased and reprogrammed without affecting other sectors. A sector is typically erased and verified within 1

second (if already completely preprogrammed). The MBM29F016A is erased when shipped from the factory.

The MBM29F016A device also features hardware sector group protection. This feature will disable both program

and erase operations in any combination of eight sector groups of memory. A sector group consists of four

adjacent sectors grouped in the following pattern: sectors 0-3, 4-7, 8-11, 12-15, 16-19, 20-23, 24-27, and 28-31.

Fujitsu has implemented an Erase Suspend feature that enables the user to put erase on hold for any period of

time to read data from or program data to a non-busy sector. Thus, true background erase can be achieved.

The device features single 5.0 V power supply operation for both read and program functions. Internally generated

and regulated voltages are provided for the program and erase operations. A low VCC detector automatically

inhibits write operations during power transitions. The end of program or erase is detected by Data Polling of

DQ7, or by the Toggle Bit I feature on DQ6 or RY/BY output pin. Once the end of a program or erase cycle has

been completed, the device automatically resets to the read mode.

The MBM29F016A also has a hardware RESET pin. When this pin is driven low, execution of any Embedded

Program or Embedded Erase operations will be terminated. The internal state machine will then be reset into

the read mode. The RESET pin may be tied to the system reset circuity. Therefore, if a system reset occurs

during the Embedded Program or Embedded Erase operation, the device will be automatically reset to a read

mode. This will enable the system microprocessor to read the boot-up firmware from the Flash memory.

Fujitsu's Flash technology combines years of EPROM and E2PROM experience to produce the highest levels

of quality, reliability, and cost effectiveness. The MBM29F016A memory electrically erases all bits within a sector

simultaneously via Fowler-Nordheim tunneling. The bytes are programmed one byte at a time using the EPROM

programming mechanism of hot electron injection.

3

Share Link: