datasheetbank_Logo
Integrated circuits, Transistor, Semiconductors Search and Datasheet PDF Download Site

ISL95870B View Datasheet(PDF) - Intersil

Part Name
Description
View to exact match
ISL95870B Datasheet PDF : 29 Pages
1 2 3 4 5 6 7 8 9 10 Next Last
ISL95870, ISL95870A, ISL95870B
ISL95870A Functional Pin Descriptions
PIN NUMBER SYMBOL
DESCRIPTION
1
LGATE Low-side MOSFET gate driver output. Connect to the gate terminal of the low-side MOSFET of the
converter.
2
PGND Return current path for the LGATE MOSFET driver. Connect to the source of the low-side MOSFET.
3
GND IC ground for bias supply and signal reference.
4
RTN Negative remote sense input of VOUT. If resistor divider consisting of RFB and ROFS is used at FB pin,
the same resistor divider should be used at RTN pin, i.e. keep RFB1=RFB, and ROFS1=ROFS.
5
VID1 Logic input for setpoint voltage selector. Use in conjunction with the VID0 pin to select among four
setpoint reference voltages.
6
VID0 Logic input for setpoint voltage selector. Use in conjunction with the VID1 pin to select among four
setpoint reference voltages.
7
SREF Soft-start and voltage slew-rate programming capacitor input and setpoint reference voltage
programming resistor input. Connects internally to the inverting input of the VSET voltage setpoint
amplifier.
8
SET0 Voltage set-point programming resistor input.
9
SET1 Voltage set-point programming resistor input.
10
FB Voltage feedback sense input. Connects internally to the inverting input of the control-loop error
transconductance amplifier. The converter is in regulation when the voltage at the FB pin equals the
voltage on the SREF pin.
11
OCSET Input for the overcurrent detection circuit. The overcurrent setpoint programming resistor ROCSET
connects from this pin to the sense node.
12
VO Output voltage sense input for the R4 modulator. The VO pin also serves as the reference input for
the overcurrent detection circuit.
13
FSEL Input for programming the regulator switching frequency. Pull this pin to VCC for 1MHz switching.
Pull this pin to GND with a 100kΩ resistor for 600kHz switching. Leave this pin floating for 500kHz
switching. Pull this pin directly to GND for 300kHz switching.
14
PGOOD Power-good open-drain indicator output. This pin changes to high impedance when the converter is
able to supply regulated voltage.
15
EN Enable input for the IC. Pulling EN above the rising threshold voltage initializes the soft-start
sequence.
16
PHASE Return current path for the UGATE high-side MOSFET driver, VIN sense input for the R4 modulator,
and inductor current polarity detector input.
17
UGATE High-side MOSFET gate driver output. Connect to the gate terminal of the high-side MOSFET of the
converter.
18
BOOT Positive input supply for the UGATE high-side MOSFET gate driver. The BOOT pin is internally
connected to the cathode of the Schottky boot-strap diode. Connect an MLCC between the BOOT pin
and the PHASE pin.
19
VCC Input for the IC bias voltage. Connect +5V to the VCC pin and decouple with at least a MLCC to the
GND pin.
20
PVCC Input for the LGATE and UGATE MOSFET driver circuits. The PVCC pin is internally connected to the
anode of the Schottky boot-strap diode. Connect +5V to the PVCC pin and decouple with a MLCC to
the PGND pin.
8
FN6899.0
December 22, 2009
 

Share Link: 

datasheetbank.com [ Privacy Policy ] [ Request Datasheet ] [ Contact Us ]