6269BIRZ View Datasheet(PDF) - Intersil

Part Name

Description

View to exact match

6269BIRZ

High-Performance Notebook PWM Controller with Audio-Frequency Clamp

Intersil 

ISL6269B

Electrical Specifications

PARAMETER

These specifications apply for TA = -40°C to +100°C, unless otherwise stated.

All typical specifications TA = +25°C, VCC = 5V, PVCC = 5V, VIN = 15V (Continued)

SYMBOL

TEST CONDITIONS

MIN TYP

PROTECTION

ISEN OCP Threshold

IOC

ISEN sourcing, TA = -10°C to +100°C

ISEN sourcing

19

26

17

26

ISEN Short-Circuit Threshold

UVP Threshold

OVP Rising Threshold

OVP Falling Threshold

OTP Rising Threshold (Note 3)

OTP Hysteresis (Note 3)

NOTE:

3. Guaranteed by characterization.

ISC

VUV

VOVR

VOVF

TOTR

TOTHYS

ISEN sourcing

-

50

81

84

113 116

100 103

-

150

-

25

MAX

33

33

-

87

119

106

-

-

UNIT

μA

μA

μA

%

%

%

°C

°C

Functional Pin Descriptions

GND (Bottom Pad)

Signal common of the IC. Unless otherwise stated, signals

are referenced to the GND pin, not the PGND pin.

VIN (Pin 1)

The VIN pin measures the converter input voltage which is a

required input to the R3 PWM modulator. Connect across

the drain of the high-side MOSFET to the GND pin.

VCC (Pin 2)

The VCC pin is the input bias voltage for the IC. Connect

+5V from the VCC pin to the GND pin. Decouple with at least

1µF of a MLCC capacitor from the VCC pin to the GND pin.

FCCM (Pin 3)

The FCCM pin configures the controller to operate in forced-

continuous-conduction-mode (FCCM) or diode-emulation-

mode (DEM.) DEM is disabled when the FCCM pin is pulled

above the rising threshold voltage VFCCMTHR, conversely

DEM is enabled when the FCCM pin is pulled below the

falling threshold voltage VFCCMTHF.

EN (Pin 4)

The EN pin is the on/off switch of the IC. The soft-start

sequence begins when the EN pin is pulled above the rising

threshold voltage VENTHR and VVCC is above the power-on

reset (POR) rising threshold voltage VVCC_THR. When the

EN pin is pulled below the falling threshold voltage VENTHF

PWM immediately stops.

COMP (Pin 5)

The COMP pin is the output of the control-loop error

amplifier. Compensation components for the control-loop

connect across the COMP and FB pins.

FB (Pin 6)

The FB pin is the inverting input of the control-loop error

amplifier. The converter output voltage regulates to 600mV

from the FB pin to the GND pin. Program the desired output

voltage with a resistor network connected across the VO,

FB, and GND pins. Select the resistor values such that FB to

GND is 600mV when the converter output voltage is at the

programmed regulation value.

FSET (Pin 7)

The FSET pin programs the PWM switching frequency.

Program the desired PWM frequency with a resistor and a

capacitor connected across the FSET and GND pins.

VO (Pin 8)

The VO pin measures the converter output voltage and is

used exclusively as an input to the R3 PWM modulator.

Connect at the physical location where the best output

voltage regulation is desired.

ISEN (Pin 9)

The ISEN pin programs the threshold of the OCP

overcurrent fault protection. Program the desired OCP

threshold with a resistor connected across the ISEN and

PHASE pins. The OCP threshold is programmed to detect

the peak current of the output inductor. The peak current is

the sum of the DC and AC components of the inductor

current.

PGND (Pin 10)

The PGND pin conducts the turn-off transient current

through the LG gate driver. The PGND pin must be

connected to complete the pulldown circuit of the LG gate

driver. The PGND pin should be connected to the source of

the low-side MOSFET through a low impedance path,

preferably in parallel with the trace connecting the LG pin to

the gate of the low-side MOSFET. The adaptive shoot-

through protection circuit, measures the low-side MOSFET

gate-source voltage from the LG pin to the PGND pin.

LG (Pin 11)

The LG pin is the output of the low-side MOSFET gate

driver. Connect to the gate of the low-side MOSFET.

6

FN6280.2

May 30, 2007

Share Link: