datasheetbank_Logo
Integrated circuits, Transistor, Semiconductors Search and Datasheet PDF Download Site

ISL6217CVZA View Datasheet(PDF) - Intersil

Part Name
Description
View to exact match
ISL6217CVZA Datasheet PDF : 19 Pages
1 2 3 4 5 6 7 8 9 10 Next Last
NOT RECSOEMEMSEU®NBDSIETSDILT6UFD2OT1aER7taAPNSREhOWeDeDUtECSTIGNS
December 2006
ISL6217
FN9089.3
Precision Multi-Phase Buck PWM
Controller for Intel‚ Mobile Voltage
Positioning IMVP-IV™and IMVP-IV+™
The ISL6217 Multi-Phase Buck PWM control IC, with
integrated half bridge gate drivers, provides a precision
voltage regulation system for advanced Pentium“ IV
microprocessors in notebook computers. Two-phase
operation eases the thermal management issues and load
demand of Intel’s latest high performance processors. This
control IC also features both input voltage feed-forward and
average current mode control for excellent dynamic
response, “Loss-less” current sensing using MOSFET
RDS(ON) and user selectable switching frequencies from
250kHz to 1MHz per phase.
The ISL6217 includes a 6-bit digital-to-analog converter
(DAC) that dynamically adjusts the CORE PWM output
voltage from 0.700V to 1.708V in 16mV steps and conforms
to the Intel IMVP-IV™ and IMVP-IV+™ mobile VID
specification. The ISL6217 also has logic inputs to select
Active, Deep Sleep and Deeper Sleep modes of operation.
A precision reference, remote sensing and proprietary
architecture, with integrated processor-mode compensated
“Droop”, provide excellent static and dynamic CORE voltage
regulation.
To improve efficiency at light loading, the ISL6217 can be
configured to run in single phase PWM in ACTIVE, DEEP or
DEEPER SLEEP modes of operation.
Another feature of this IC controller is the PGOOD monitor
circuit that is held low until CORE voltage increases, during
its soft-start sequence, to within 12% of the “Boot” voltage.
This PGOOD signal is masked during VID changes. Output
Overcurrent, Overvoltage and Undervoltage are monitored
and result in the converter latching off and PGOOD signal
being held low.
The Overvoltage and Undervoltage thresholds are 112%
and 84% of the VID, Deep or Deeper Sleep setpoint,
respectively. Overcurrent protection features a 32 cycle
Overcurrent shutdown. PGOOD, Overvoltage, Undervoltage
and Overcurrent provide monitoring and protection for the
microprocessor and power system. The ISL6217 IC is
available in a 38 lead TSSOP.
Features
IMVP-IV™ and IMVP-IV+™ Compliant CORE Regulator
Single and/or Two-phase Power Conversion
“Loss-less” Current sensing for improved efficiency and
reduced board area
Optional Discrete Precision Current Sense Resistor
Internal Gate-Drive and Boot-Strap Diodes
Precision CORE Voltage Regulation
0.8% system accuracy over temperature
6-Bit Microprocessor Voltage Identification Input
Programmable “Droop” and CORE Voltage Slew Rate to
comply with IMVP-IV™ and IMVP-IV+™ specification
Direct Interface with System Logic (STP_CPU# and
DPRSLPVR) for Deep and Deeper Sleep modes of
operation
Easily Programmable voltage setpoints for Initial “Boot”,
Deep Sleep and Deeper Sleep Modes
Excellent Dynamic Response
Combined Voltage Feed-Forward and Average
Current Mode Control
Overvoltage, Undervoltage and Overcurrent Protection
Power-Good Output with internal blanking during VID and
mode changes
User programmable Switching Frequency of 250kHz -
1MHz per phase
Pb-Free Plus Anneal Available (RoHS Compliant)
Ordering Information
PART NUMBER TEMP (°C)
PACKAGE
PKG.
DWG. #
ISL6217CV
-10 to 85 38 Ld TSSOP
M38.173
ISL6217CV-T 38 Ld TSSOP Tape and Reel
M38.173
ISL6217CVZ
(Note 1)
-10 to 85 38 Ld TSSOP
(Pb-free)
M38.173
ISL6217CVZ-T 38 Ld TSSOP Tape and Reel
(Note 1)
(Pb-free)
M38.173
ISL6217CVZA
(Note 1)
-10 to 85 38 Ld TSSOP
(Pb-free)
M38.173
ISL6217CVZA-T 38 Ld TSSOP Tape and Reel
(Note 1)
(Pb-free)
M38.173
NOTES:
1. Intersil Pb-free plus anneal products employ special Pb-free
material sets; molding compounds/die attach materials and 100%
matte tin plate termination finish, which are RoHS compliant and
compatible with both SnPb and Pb-free soldering operations. Intersil
Pb-free products are MSL classified at Pb-free peak reflow
temperatures that meet or exceed the Pb-free requirements of
IPC/JEDEC J STD-020.
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 321-724-7143|Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright © Intersil Americas Inc. 2006. All Rights Reserved
All other trademarks mentioned are the property of their respective owners
 

Share Link: 

datasheetbank.com [ Privacy Policy ] [ Request Datasheet ] [ Contact Us ]