datasheetbank_Logo   Integrated circuits, Transistor, Semiconductors Search and Datasheet PDF Download Site
Part Name :   

ISL22343WFR20Z View Datasheet(PDF) - Intersil

Part NameDescriptionManufacturer
ISL22343WFR20Z Quad Digitally Controlled Potentiometer (XDCP™) Intersil
Intersil Intersil
ISL22343WFR20Z Datasheet PDF : 19 Pages
1 2 3 4 5 6 7 8 9 10 Next Last
ISL22343
Operating Specifications Over the recommended operating conditions unless otherwise specified. (Continued)
SYMBOL
ISB
IV-SB
ISD
IV-SD
PARAMETER
VCC Current (Standby)
V- Current (Standby)
VCC Current (Shutdown)
V- Current (Shutdown)
TEST CONDITIONS
VCC = +5.5V, V- = -5.5V @ +85°C, I2C interface in
standby state
VCC = +5.5V, V- = -5.5V @ +125°C, I2C interface in
standby state
VCC = +2.25V, V- = -2.25V @ +85°C, I2C interface in
standby state
VCC = +2.25V, V- = -2.25V @ +125°C, I2C interface in
standby state
V- = -5.5V, VCC = +5.5V @ +85°C, I2C interface in
standby state
V- = -5.5V, VCC = +5.5V @ +125°C, I2C interface in
standby state
V- = -2.25V, VCC = +2.25V @ +85°C, I2C interface in
standby state
V- = -2.25V, VCC = +2.25V @ +125°C, I2C interface in
standby state
VCC = +5.5V, V- = -5.5V @ +85°C, I2C interface in
standby state
VCC = +5.5V, V- = -5.5V @ +125°C, I2C interface in
standby state
VCC = +2.25V, V- = -2.25V @ +85°C, I2C interface in
standby state
VCC = +2.25V, V- = -2.25V @ +125°C, I2C interface in
standby state
V- = -5.5V, VCC = +5.5V @ +85°C, I2C interface in
standby state
V- = -5.5V, VCC = +5.5V @ +125°C, I2C interface in
standby state
V- = -2.25V, VCC = +2.25V @ +85°C, I2C interface in
standby state
V- = -2.25V, VCC = +2.25V @ +125°C, I2C interface in
standby state
MIN
(Note 21)
-4.0
-5.0
-2.0
-3.0
-4.0
-5.0
-2.0
-3.0
TYP
MAX
(Note 5) (Note 21)
0.5
2.0
1.0
4.0
0.2
1.0
0.5
2.0
-0.7
-1.5
-0.3
-0.4
0.5
2.0
1.0
4.0
0.2
1.0
0.5
2.0
-0.7
-1.5
-0.3
-0.4
ILkgDig
Leakage Current, at Pins Voltage at pin from GND to VCC
A0, A1, A2, SDA, and SCL
-1
1
tWRT
DCP Wiper Response
SCL falling edge of last bit of DCP data byte to wiper
1.5
(Note 19) Time
new position
tShdnRec DCP Recall Time from
SCL falling edge of last bit of ACR data byte to wiper
1.5
(Note 19) Shutdown Mode
stored position and RH connection
Vpor
Power-on Recall Voltage Minimum VCC at which memory recall occurs
1.9
2.1
VCCRamp VCC Ramp Rate
0.2
tD
Power-up Delay
VCC above
completed,
Vpor, to
and I2C
DCP Initial
Interface in
Value Register
standby state
recall
5
EEPROM SPECIFICATION
EEPROM Endurance
1,000,000
EEPROM Retention
Temperature T +55°C
50
tWC
Non-volatile Write Cycle
(Note 20) Time
12
20
UNIT
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µs
µs
V
V/ms
ms
Cycles
Years
ms
6
FN6423.2
August 17, 2015
Direct download click here
 

Share Link : Intersil
All Rights Reserved © datasheetbank.com 2014 - 2019 [ Privacy Policy ] [ Request Datasheet ] [ Contact Us ]