datasheetbank_Logo
Integrated circuits, Transistor, Semiconductors Search and Datasheet PDF Download Site

ISL22313TFU10Z View Datasheet(PDF) - Intersil

Part Name
Description
View to exact match
ISL22313TFU10Z Datasheet PDF : 15 Pages
1 2 3 4 5 6 7 8 9 10 Next Last
ISL22313
Operating Specifications Over the recommended operating conditions unless otherwise specified. Limits are established by
characterization. (Continued)
SYMBOL
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
(Note 18) (Note 4) (Note 18) UNIT
tSU:A A1 and A0 setup time
Before START condition
600
ns
tHD:A A1 and A0 hold time
After STOP condition
600
ns
NOTES:
4. Typical values are for TA = +25°C and 3.3V supply voltage.
5. LSB: [V(RW)255 – V(RW)0]/255. V(RW)255 and V(RW)0 are V(RW) for the DCP register set to FF hex and 00 hex respectively. LSB is the
incremental voltage when changing from one tap to an adjacent tap.
6. ZS error = V(RW)0/LSB.
7. FS error = [V(RW)255 – VCC]/LSB.
8. DNL = [V(RW)i – V(RW)i-1]/LSB-1, for i = 1 to 255. i is the DCP register setting.
9. INL = [V(RW)i – i • LSB – V(RW)0]/LSB for i = 1 to 255
10.
TCV
=
-------M-----a----x----(--V----(---R-----W------)--i--)---–-----M-----i--n----(--V-----(--R-----W------)--i--)------ × ----1----0---6----- for i = 16 to 255 decimal, T = -40°C to +125°C. Max( ) is the maximum value of the wiper
[Max(V(RW)i) + Min(V(RW)i)] ⁄ 2 +165°C voltage and Min ( ) is the minimum value of the wiper voltage over the temperature range.
11. MI = |RW255 – RW0|/255. MI is a minimum increment. RW255 and RW0 are the measured resistances for the DCP register set to FF hex and
00 hex respectively.
12. Roffset = RW0/MI, when measuring between RW and RL.
Roffset = RW255/MI, when measuring between RW and RH.
13. RDNL = (RWi – RWi-1)/MI -1, for i = 16 to 255.
14. RINL = [RWi – (MI • i) – RW0]/MI, for i = 16 to 255.
15.
TCR
= ----[---M-----a----x----(--R-----i--)---–-----M-----i--n----(--R-----i--)--]---- × ----1----0---6-----
[Max(Ri) + Min(Ri)] ⁄ 2 +165°C
for i = 16 to 255, T = -40°C to +125°C. Max( ) is the maximum value of the resistance and Min ( ) is
the minimum value of the resistance over the temperature range.
16. Limits should be considered typical and are not production tested.
17. tWC is the time from a valid STOP condition at the end of a Write sequence of I2C serial interface, to the end of the self-timed internal non-volatile
write cycle.
18. Parts are 100% tested at +25°C. Over temperature limits established by characterization and are not production tested.
DCP Macro Model
RTOTAL
RH
RL
CL
CH
CW
10pF
10pF
25pF
RW
SDA vs SCL Timing
SCL
tSU:STA
SDA
(INPUT TIMING)
tF
tHIGH
tSU:DAT
tHD:STA
SDA
(OUTPUT TIMING)
tLOW
tHD:DAT
tR
tsp
tAA tDH
tSU:STO
tBUF
7
FN6421.0
July 17, 2007
 

Share Link: 

datasheetbank.com [ Privacy Policy ] [ Request Datasheet ] [ Contact Us ]