datasheetbank_Logo   Integrated circuits, Transistor, Semiconductors Search and Datasheet PDF Download Site
Part Name :   

ISL22313TFU10Z-TK View Datasheet(PDF) - Intersil

Part NameDescriptionManufacturer
ISL22313TFU10Z-TK Single Digitally Controlled Potentiometer (XDCP™) Intersil
Intersil Intersil
ISL22313TFU10Z-TK Datasheet PDF : 15 Pages
1 2 3 4 5 6 7 8 9 10 Next Last
ISL22313
Operating Specifications Over the recommended operating conditions unless otherwise specified. Limits are established by
characterization. (Continued)
SYMBOL
PARAMETER
ISB
VCC Current (standby)
IV-SB V- Current (standby)
ISD
VCC Current (shutdown)
IV-SB V- Current (standby)
TEST CONDITIONS
VCC = +5.5V, V- = -5.5V @ +85°C, I2C
interface in standby state
VCC = +5.5V, V- = -5.5V @ +125°C, I2C
interface in standby state
VCC = +2.25V, V- = -2.25V @ +85°C, I2C
interface in standby state
VCC = +2.25V, V- = -2.25V @ +125°C, I2C
interface in standby state
V- = -5.5V, VCC = +5.5V @ +85°C, I2C
interface in standby state
V- = -5.5V, VCC = +5.5V @ +125°C, I2C
interface in standby state
V- = -2.25V, VCC = +2.25V @ +85°C, I2C
interface in standby state
V- = -2.25V, VCC = +2.25V @ +125°C, I2C
interface in standby state
VCC = +5.5V, V- = -5.5V @ +85°C, I2C
interface in standby state
VCC = +5.5V, V- = -5.5V @ +125°C, I2C
interface in standby state
VCC = +2.25V, V- = -2.25V @ +85°C, I2C
interface in standby state
VCC = +2.25V, V- = -2.25V @ +125°C, I2C
interface in standby state
V- = -5.5V, VCC = +5.5V @ +85°C, I2C
interface in standby state
V- = -5.5V, VCC = +5.5V @ +125°C, I2C
interface in standby state
V- = -2.25V, VCC = +2.25V @ +85°C, I2C
interface in standby state
V- = -2.25V, VCC = +2.25V @ +125°C, I2C
interface in standby state
MIN
TYP
MAX
(Note 18) (Note 4) (Note 18)
0.2
1.5
1
2.5
0.1
1
0.5
2
-2.5
-0.7
-4
-3
-1.5
-0.3
-3
-1
0.2
1.5
1
2.5
0.1
1
0.5
2
-2.5
-0.7
-4
-3
-1.5
-0.3
-3
-1
ILkgDig Leakage current, at pins A0, A1, SDA, Voltage at pin from GND to VCC
-1
1
and SCL
tDCP
DCP wiper response time
SCL falling edge of last bit of DCP data byte
1.5
(Note 16)
to wiper new position
tShdnRec DCP recall time from shutdown mode SCL falling edge of last bit of ACR data byte
1.5
(Note 16)
to wiper stored position and RH connection
Vpor Power-on recall voltage
Minimum VCC at which memory recall occurs 1.9
2.1
VCC Ramp VCC ramp rate
0.2
tD
Power-up delay
VCC above Vpor, to DCP Initial Value
5
Register recall completed, and I2C Interface
in standby state
EEPROM SPECIFICATION
EEPROM Endurance
1,000,000
EEPROM Retention
Temperature T +55°C
50
tWC
Non-volatile Write cycle time
(Note 17)
12
20
UNIT
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µs
µs
V
V/ms
ms
Cycles
Years
ms
5
FN6421.0
July 17, 2007
Direct download click here
 

Share Link : Intersil
All Rights Reserved © datasheetbank.com 2014 - 2019 [ Privacy Policy ] [ Request Datasheet ] [ Contact Us ]