datasheetbank_Logo     Integrated circuits, Transistor, Semiconductors Search and Datasheet PDF Download Site

ISL1208IB8-TK View Datasheet(PDF) - Intersil

Part NameDescriptionManufacturer
ISL1208IB8-TK I2CŪ Real Time Clock/Calendar Intersil
Intersil Intersil
ISL1208IB8-TK Datasheet PDF : 24 Pages
First Prev 11 12 13 14 15 16 17 18 19 20 Next Last
ISL1208
FREQUENCY OUT CONTROL BITS (FO <3:0>)
These bits enable/disable the frequency output function and
select the output frequency at the IRQ/fOUT pin. See
Table 4 for frequency selection. When the frequency mode is
enabled, it will override the alarm mode at the IRQ/fOUT pin.
TABLE 4. FREQUENCY SELECTION OF fOUT PIN
FREQUENCY,
fOUT
UNITS
0
Hz
FO3
0
FO2 FO1 FO0
0
0
0
32768
Hz
0
0
0
1
4096
Hz
0
0
1
0
1024
Hz
0
0
1
1
64
Hz
0
1
0
0
32
Hz
0
1
0
1
16
Hz
0
1
1
0
8
Hz
0
1
1
1
4
Hz
1
0
0
0
2
Hz
1
0
0
1
1
Hz
1
0
1
0
1/2
Hz
1
0
1
1
1/4
Hz
1
1
0
0
1/8
Hz
1
1
0
1
1/16
Hz
1
1
1
0
1/32
Hz
1
1
1
1
FREQUENCY OUTPUT AND INTERRUPT BIT (FOBATB)
This bit enables/disables the fOUT/IRQ pin during battery
backup mode (i.e. VBAT power source active). When the
FOBATB is set to “1” the fOUT/IRQ pin is disabled during
battery backup mode. This means that both the frequency
output and alarm output functions are disabled. When the
FOBATB is cleared to “0”, the fOUT/IRQ pin is enabled
during battery backup mode.
LOW POWER MODE BIT (LPMODE)
This bit enables/disables low power mode. With
LPMODE = “0”, the device will be in normal mode and the
VBAT supply will be used when VDD < VBAT - VBATHYS and
VDD < VTRIP. With LPMODE = “1”, the device will be in low
power mode and the VBAT supply will be used when
VDD < VBAT - VBATHYS. There is a supply current saving of
about 600nA when using LPMODE = “1” with VDD = 5V.
(See Typical Performance Curves on page 7: IDD vs VCC
with LPMODE ON and OFF.) Avoid setting the device into
low power mode with VDD < VBAT, the I2C communications
will stop permanently. The VBAT input must be lowered
below VDD to resume communications.
ALARM ENABLE BIT (ALME)
This bit enables/disables the alarm function. When the ALME
bit is set to “1”, the alarm function is enabled. When the ALME
is cleared to “0”, the alarm function is disabled. The alarm
function can operate in either a single event alarm or a periodic
interrupt alarm (see IM bit).
NOTE: When the frequency output mode is enabled, the alarm function
is disabled.
INTERRUPT/ALARM MODE BIT (IM)
This bit enables/disables the interrupt mode of the alarm
function. When the IM bit is set to “1”, the alarm will operate
in the interrupt mode, where an active low pulse width of
250ms will appear at the IRQ/fOUT pin when the RTC is
triggered by the alarm as defined by the alarm registers (0Ch
to 11h). When the IM bit is cleared to “0”, the alarm will
operate in standard mode, where the IRQ/fOUT pin will be
tied low until the ALM status bit is cleared to “0”.
IM BIT
0
1
INTERRUPT/ALARM FREQUENCY
Single Time Event Set By Alarm
Repetitive/Recurring Time Event Set By Alarm
Analog Trimming Register
ANALOG TRIMMING REGISTER (ATR<5:0>)
X1
CX1
X2
CX2
CRYSTAL
OSCILLATOR
FIGURE 11. DIAGRAM OF ATR
Six analog trimming bits, ATR0 to ATR5, are provided in
order to adjust the on-chip load capacitance value for
frequency compensation of the RTC. Each bit has a different
weight for capacitance adjustment. For example, using a
Citizen CFS-206 crystal with different ATR bit combinations
provides an estimated ppm adjustment range from -34ppm
to +80ppm to the nominal frequency compensation. The
combination of analog and digital trimming can give up to
-94ppm to +140ppm of total adjustment.
The effective on-chip series load capacitance, CLOAD,
ranges from 4.5pF to 20.25pF with a mid-scale value of
12.5pF (default). CLOAD is changed via two digitally
controlled capacitors, CX1 and CX2, connected from the X1
and X2 pins to ground (see Figure 11). The value of CX1 and
CX2 are given in Equation 1:
CX = (16 ⋅ b5 + 8 ⋅ b4 + 4 ⋅ b3 + 2 ⋅ b2 + 1 ⋅ b1 + 0.5 ⋅ b0 + 9)pF (EQ. 1)
13
FN8085.8
September 12, 2008
Direct download click here

 

Share Link : 

All Rights Reserved ÂĐ datasheetbank.com 2014 - 2019 [ Privacy Policy ] [ Request Datasheet ] [ Contact Us ]