datasheetbank_Logo   Integrated circuits, Transistor, Semiconductors Search and Datasheet PDF Download Site
Part Name :   

ISL12020M View Datasheet(PDF) - Intersil

Part NameDescriptionManufacturer
ISL12020M Low Power RTC with Battery Backed SRAM,Integrated ±5ppm Temperature Compensation and Auto Daylight Saving Intersil
Intersil Intersil
ISL12020M Datasheet PDF : 32 Pages
First Prev 21 22 23 24 25 26 27 28 29 30 Next Last
ISL12020M
TABLE 17. FINAL ANALOG TRIMMING REGISTER
ADDR 7 6 5
4
3
2
1
0
0Eh 0 0 FATR5 FATR4 FATR3 FATR2 FATR1 FATR0
Final Digital Trimming Register (FDTR)
This register shows the final setting of DT after
temperature correction. It is read-only; the user cannot
overwrite a value to this register. The value is accessible
as a means of monitoring the temperature compensation
function. The corresponding clock adjustment values are
shown in Table 19. The FDTR setting has both positive
and negative settings to adjust for any offset in the
crystal.
.
TABLE 18. FINAL DIGITAL TRIMMING REGISTER
ADDR 7 6 5
4
3
2
1
0
0Fh 0 0 0 FDTR4 FDTR3 FDTR2 FDTR1 FDTR0
TABLE 19. CLOCK ADJUSTMENT VALUES FOR FINAL
DIGITAL TRIMMING REGISTER
FDTR<2:0>
DECIMAL
ppm
ADJUSTMENT
00000
0
0
00001
1
30.5
00010
2
61
00011
3
91.5
00100
4
122
00101
5
152.5
00110
6
183
00111
7
213.5
01000
8
244
01001
9
274.5
01010
10
305
10000
0
0
10001
-1
-30.5
10010
-2
-61
10011
-3
-91.5
10100
-4
-122
10101
-5
-152.5
10110
-6
-183
10111
-7
-213.5
11000
-8
-244
11001
-9
-274.5
11010
-10
-305
ALARM Registers (10h to 15h)
The alarm register bytes are set up identical to the RTC
register bytes, except that the MSB of each byte
functions as an enable bit (enable = “1”). These enable
bits specify which alarm registers (seconds, minutes,
etc.) are used to make the comparison. Note that there
is no alarm byte for year.
The alarm function works as a comparison between the
alarm registers and the RTC registers. As the RTC
advances, the alarm will be triggered once a match
occurs between the alarm registers and the RTC
registers. Any one alarm register, multiple registers, or
all registers can be enabled for a match.
There are two alarm operation modes: Single Event and
periodic Interrupt Mode:
Single Event Mode is enabled by setting the bit 7
on any of the Alarm registers (ESCA0... EDWA0) to
“1”, the IM bit to “0”, and disabling the frequency
output. This mode permits a one-time match
between the Alarm registers and the RTC registers.
Once this match occurs, the ALM bit is set to “1” and
the IRQ/FOUT output will be pulled low and will
remain low until the ALM bit is reset. This can be
done manually or by using the auto-reset feature.
Interrupt Mode is enabled by setting the bit 7 on
any of the Alarm registers (ESCA0... EDWA0) to “1”,
the IM bit to “1”, and disabling the frequency output.
The IRQ/FOUT output will now be pulsed each time
an alarm occurs. This means that once the interrupt
mode alarm is set, it will continue to alarm for each
occurring match of the alarm and present time. This
mode is convenient for hourly or daily hardware
interrupts in microcontroller applications such as
security cameras or utility meter reading.
To clear a single event alarm, the ALM bit in the status
register must be set to “0” with a write. Note that if the
ARST bit is set to 1 (address 08h, bit 7), the ALM bit will
automatically be cleared when the status register is read.
Following are examples of both Single Event and periodic
Interrupt Mode alarms.
Example 1
• Alarm set with single interrupt (IM = “0”)
• A single alarm will occur on January 1 at 11:30 a.m.
• Set Alarm registers as follows:
ALARM
BIT
REGISTER 7 6 5 4 3 2 1 0 HEX DESCRIPTION
SCA0
0 0 0 0 0 0 0 0 00h Seconds
disabled
MNA0
1 0 1 1 0 0 0 0 B0h Minutes set to
30, enabled
HRA0
1 0 0 1 0 0 0 1 91h Hours set to 11,
enabled
DTA0
1 0 0 0 0 0 0 1 81h Date set to 1,
enabled
MOA0
1 0 0 0 0 0 0 1 81h Month set to 1,
enabled
DWA0
0 0 0 0 0 0 0 0 00h Day of week
disabled
21
FN6667.4
February 11, 2010
Direct download click here
 

Share Link : Intersil
All Rights Reserved © datasheetbank.com 2014 - 2019 [ Privacy Policy ] [ Request Datasheet ] [ Contact Us ]