datasheetbank_Logo
Integrated circuits, Transistor, Semiconductors Search and Datasheet PDF Download Site

LP2950 View Datasheet(PDF) - Calogic, LLC

Part Name
Description
View to exact match
LP2950 Datasheet PDF : 10 Pages
1 2 3 4 5 6 7 8 9 10
CORPORATION
LP2950 / LP2951
ELECTRICAL CHARACTERISTICS (continued)
PARAMETER
ERROR COMPARATOR
Output Leakage Current
Output Low Voltage
Upper Threshold Voltage
Lower Threshold Voltage
Hysteresis
SHUTDOWN INPUT
Input Logic Voltage
Shutdown Pin
Input Current
Regulator Output Current
in Shutdown
LP2951
LP2950AC / LP2951AC LP2950C / LP2951C
UNITS
MIN TYP MAX MIN TYP MAX MIN TYP MAX
CONDITIONS
(Note 2)
0.01 1
0.01 1
0.01 1
150 250
150 250
150 250
40 60
40
60
40 60
75 95
75
95
75 95
15
15
15
µA VOH = 30V
mV VIN = 4.5V, IOL = 400µA
mV (Note 7)
mV (Note 7)
mV (Note 7)
1.3 0.6
1.3 0.7
1.3 0.7
2
2
2
V
Low (Regulator ON)
V
High (Regulator OFF)
30 50
675 800
30
50
675 800
30 50
675 800
µA VS = 2.4V
µA VS = 30V
3
10
3
10
3
10
µA (Note 9)
Note 1: Output or reference voltage temperature coefficients defined as the worst case voltage change divided by the total temperature range.
Note 2: Unless otherwise specified all limits guaranteed for TJ = 25oC, VIN = 6V, IL=100µA and CL = 1µF. Additional conditions for the 8-pin
versions are feedback tied to 5V tap and output tied to output Sense (VOUT = 5V) and VSHUTDOWN 0.8V.
Note 3: Regulation is measured at constant junction temperature, using pulse testing with a low duty cycle. Changes in output voltage due to
heating effects are covered under the specification for thermal regulation.
Note 4: Line regulation for the LP2951 is tested at 150oC for IL = 1mA. For IL = 100µA and TJ = 125oC, line regulation is guaranteed by design to
0.2%. See typical performance characteristics for line regulation versus temperature and load current.
Note 5: Dropout voltage is defined as the input to output differential at which the output voltage drops 100mV below its nominal value measured
at 1V differential at very low values of programmed output voltage, the minimum input supply voltage of 2V (2.3V over temperature) must be
taken input account.
Note 6: VREF VOUT (VIN - 1V), 2.3 VIN 30V, 100µA IL 100mA, TJ TJMAX.
Note 7: Comparator thresholds are expressed in terms of a voltage differential at the feedback terminal below the nominal reference voltage
measured at 6V input. To express these thresholds in terms of output voltage change, multiply by the error amplifier gain = VOUT/VREF =
(R1+R2)/R2. For example, at a programmed output voltage of 5V, the error output is guaranteed to go low when the output drops by 95mV x
5V/1.235 = 384mV. Thresholds remain constant as a percent of VOUT as VOUT is varied, with the dropout warning occurring at typically 5% below
nominal, 7.5% guaranteed.
Note 8: VSHUTDOWN 2V, VIN 30V, VOUT = 0, Feedback pin tied to 5V Tap.
Note 9: All typical values are not guaranteed.
BLOCK DIAGRAM
UNREGULATED DC
+
7
FEEDBACK
8
INPUT
1
OUTPUT
FROM
CMOS
OR TTL
3
SHUTDOWN
+
60mV
+
+
+ 1.23V
REFERENCE
LP2950 AND LP2951 BLOCK DIAGRAM
ERROR
AMPLIFIER
180k
60k
ERROR DETECTION
COMPARATOR
2
SENSE
6
5V TAP
5
ERROR
4
GROUND
5V @ 100mA
MAX
+
1µF
330k
TO CMOS OR
TTL
1D-21
CALOGIC CORPORATION, 237 Whitney Place, Fremont, California 94539, Telephone: 510-656-2900, FAX: 510-651-3025
 

Share Link: 

datasheetbank.com [ Privacy Policy ] [ Request Datasheet ] [ Contact Us ]